XCAP-LTE Lte Parameter Description Edition: 04 Version: 4.108.xx 2011. 01.
2011 2011 Accuver., Ltd., All rights reserved. This documentation shall not be changed, distributed to the public, and opened to the third person without written approval. Accuver is not responsible for any direct or indirect damages arisen or related to use of this manual. All information included herein may be changed without prior notice.
Accuver APAC Limited Unit 206, 2/F., No. 8 Science Park West Avenue Hong Kong Science Park, Shatin New Territories, Hong Kong TEL: +852 2210 7004 FAX: FAX: +852 2210 7017 Web: http://www.accuver.com Email:
[email protected]
Introduction of Appendix This Analyzer Parameter Description manual specifies asynchronous parameters in Parameter Trees in Analyzer graph/map/table/CDF/PDF.
History Edition
Date
Description
00
2009.10
Draft version (LGE)
01
2010.10
2 version (LGE)
02
2010.10
3 version (Samsung)
nd rd
th
4 version 03
2011.01
1) Qualcomm 2) Samsung – LPHY N Cell Information Structure Enhancement)
04
© Copyright by Accuver Ltd.
2011.01
th
5 version (GCT)
Page I
.............................................................. ................................................ ................ I Introduction of Appendix ..............................
History ................................................................................................... I
Parameter Description LGE ............................................................... ..................................................... .................... 1 L1 Status Info .............................. .............................................................. ............................... 2 Serving Cell Signal Quality Info ............................... ............................................................... ..................................................... .................... 2 Tx Power Info ..............................
RACH Info ....................................................................................... 2 ............................................................... .......................................... ......... 3 Timing Adjustment Info ..............................
Cell Info .......................................................................................... 3 ............................................................... ..................................................... .................... 6 Search Result .............................. ................................................................ ..................................................... .................... 7 Channel Info ...............................
CQI Info.......................................................................................... 7 ............................................................... ............................................... ............... 8 Multi-paths Profile ............................... ................................................................ ..................................................... .................... 8 PBCH BLER ............................... .............................................................. ..................................................... .................... 9 PDSCH BLER ............................. .............................................................. .......................................... ......... 9 PDCCH Detection Rate ............................. ............................................ ............... 9 DL Grant & UL Ack/Nack Status Info(Improved) .............................
DL Grant & UL Ack/Nack Status Info(Improved)[Detail per TTI] ........................ 11 UL Grant & DL Ack/Nack Status Info ....................................................... 12 UL Grant & DL Ack/Nack Status info[Detail per TTI] ..................................... 13 PDSCH PHY Throughput ................................................................... 14 UL PRB MAP Data Info ...................................................................... 14 PUSCH PHY Throughput ................................................................... 14 L2 DL Throughput ............................................................................ 15 L2 UL Throughput ............................................................................ 15 PDSCH MAC BLER .......................................................................... 16 RLC States Info ............................................................................... 16 MAC State Info ............................................................................... 17 MAC UL Transmission Info .................................................................. 17 RACH REQ Info .............................................................................. 18 RACH RSP General Info .................................................................... 18 RNTI Info ...................................................................................... 19
© Copyright by Accuver Ltd.
Page I
목차
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Serving Cell & Neighbor Cell Lists ......................................................... 19 NAS System Info ............................................................................. 21 RRC BCH Status Info ........................................................................ 22 NAS State Info ................................................................................ 22 NAS State Info(R4) ........................................................................... 22 Radio & NAS Signaling Failure Info ........................................................ 23 RRC Freq Scan Info ......................................................................... 23 Cell Reselection Info ......................................................................... 23 Handover History ............................................................................. 23 Data Path Packet Loss ...................................................................... 24 ESM Instance Info ............................................................................ 24
Samsung Common Basic Info .......................................................................... 26 Common Data Info ........................................................................... 26 LTE N Cell Information ....................................................................... 27 LPHY Cell Search Info ....................................................................... 28 LPHY System Info ............................................................................ 29 LPHY Channel Quality Info ................................................................. 30 LPHY Parameter Info ........................................................................ 30 LPHY PHICH Info ............................................................................ 31 LL1 RF & Sync Info .......................................................................... 31 LL1 Downlink Info ............................................................................ 32 LL1 Uplink Info ................................................................................ 32 LL1 Measurement Config Info .............................................................. 32 LL2 SCH Configuration Info ................................................................. 33 Timer & Preamble Info ....................................................................... 33 Power Ramping & RA Supervision Info .................................................... 33 Max HARQ Msg3Tx & RACH Info ......................................................... 34 LL2 RNTI Info ................................................................................. 34 LL2 RLC Info .................................................................................. 34 LL2 PDCP Info ................................................................................ 35 LRRC Serving Cell Info ...................................................................... 36 LRRC State Variables Info .................................................................. 36 LRRC Timer info .............................................................................. 37 LNAS State Variables Info ................................................................... 37 LNAS MM(SIM/PLMN/Security) Info ....................................................... 38
Page II
© Copyright by Accuver Ltd.
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
LNAS PDP/IP Info ............................................................................ 39 LDATA Throughput Info ...................................................................... 39 LDATA Timing Info............................................................................ 39
Qualcomm Configuration Info ............................................................................ 40 Power Info ..................................................................................... 50 Cell Search .................................................................................... 50 Ant Correlation Result ....................................................................... 51 Intrafreq Measurement Info ................................................................. 51 Channel Quality Info ......................................................................... 53 ML1 Downlink Info ........................................................................... 54 ML1 Uplink Info ............................................................................... 55 Random Access Procedure ................................................................. 55 Radio Link Monitoring Info .................................................................. 59 NAS ESM Bearer Context Info ............................................................. 59 NAS EMM State .............................................................................. 60 RRC Serving Cell Info ....................................................................... 61 RRC PLMN Search Info ..................................................................... 62 ML1 Serving Cell Info(Acquisition) ......................................................... 63 Physical Throughput ......................................................................... 63 MAC Throughput ............................................................................. 64 RLC Throughput .............................................................................. 64 PDCP Throughput ............................................................................ 64
GCT L1 Status Info ................................................................................. 66 Serving Cell Signal Quality Info ............................................................ 67 Tx Power Info ................................................................................. 67 RACH Info ..................................................................................... 67 Timing Adjustment Info ...................................................................... 67 Cell Info ........................................................................................ 68 Search Result ................................................................................. 71 Channel Info .................................................................................. 71 CQI Info........................................................................................ 72 Multi-paths Profile ............................................................................ 73 PBCH BLER .................................................................................. 73 PDSCH BLER ................................................................................ 73
© Copyright by Accuver Ltd.
Page III
목차
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
PDCCH Detection Rate ..................................................................... 74 DL Grant & UL Ack/Nack Status Info(Improved) .......................................... 74 DL Grant & UL Ack/Nack Status Info(Improved)[Detail per TTI] ........................ 76 UL Grant & DL Ack/Nack Status Info ....................................................... 77 UL Grant & DL Ack/Nack Status info[Detail per TTI] ..................................... 78 PDSCH PHY Throughput ................................................................... 78 UL PRB MAP Data Info ...................................................................... 79 PUSCH PHY Throughput ................................................................... 79 L2 DL Throughput ............................................................................ 79 L2 UL Throughput ............................................................................ 80 PDSCH MAC BLER .......................................................................... 80 RLC States Info ............................................................................... 81 MAC State Info ............................................................................... 81 MAC UL Transmission Info .................................................................. 81 RACH REQ Info .............................................................................. 83 RACH RSP General Info .................................................................... 83 RNTI Info ...................................................................................... 83 Serving Cell & Neighbor Cell Lists ......................................................... 84 NAS System Info ............................................................................. 86 RRC BCH Status Info ........................................................................ 86 NAS State Info ................................................................................ 87 NAS State Info(R4) ........................................................................... 87 Radio & NAS Signaling Failure Info ........................................................ 87 RRC Freq Scan Info ......................................................................... 87 Cell Reselection Info ......................................................................... 88 Handover History ............................................................................. 88 Data Path Packet Loss ...................................................................... 88 ESM Instance Info ............................................................................ 89
Page IV
© Copyright by Accuver Ltd.
Parameter Description
LGE L1 Status Info L1 status information shows physical layer status such as channel setup status, serving cell information, PCH DRX and measurement periodicity, etc.
Parameter State Info> Main State
Description Physical layer main state 0: DEACTIVATED 1: IDLE 2: CONNECTED
State Info> BCH
BCH Channel State 0: RELEASE 1: SETUP
State Info> PCH
PCH Channel State 0: RELEASE 1: SETUP
State Info> DL-SCH for BCCH
DL-SCH for BCCH Channel State 0: RELEASE 1: SETUP
State Info> UL/DL-SCH and RACH
UL/DL-SCH and RACH Channel State 0: RELEASE 1: SETUP
Serving Cell Info> PCI Serving Cell Info> DL Freq Serving Cell Info> UL Freq Serving Cell Info> DL Bandwidth Serving Cell Info> UL Bandwidth Serving Cell Info> Antenna Num
Cell identifier Downlink frequency
Uplink frequency
Downlink bandwidth (Unit : RB)
Uplink bandwidth (Unit : RB)
Number of downlink transmit antenna
PCH DRX Period
PCH DRX periodicity 0: 0.32sec 1: 0.64sec 2: 1.28sec 3: 2.56sec 255: OFF
Serving Cell Signal Quality Info The serving cell quality information shows SNR of reference signal (RS SNR) and received power of reference signal (RS RSSI).
Parameter
Description
RS RSSI 0
received power 0 of reference signal
RS RSSI 1
received power 1 of reference signal
RS RSSI
total received power of reference signal (rs_rssi[0] + rs_rssi[1])/2
RS SNR
reference signal power and noise power for a resource element containing RS are estimated. 10*log10{ (signal_pwr[0] + signal_pwr [1])/ (noise_pwr[0] + noise_pwr [1])})
Tx Power Info Time sync report log shows the time sync status of UE.
Parameter
Description
PUCCH Tx Power
PUSCH average UE output power in dBm
PUSCH Tx Power
PUCCH average UE output power in dBm
PRACH Tx Power
PRACH instantaneous UE output power in dBm
Total Tx Power
1 frame based average UE output power in dBm
RACH Info Parameter Frame Num TTI Preamble Format Speed Mode Root Seq Cyclic Shift Zero Correlation Zone
Description Start frame number Start subframe number 0: Format 0, 1: Format 1, 2: Format2, 3: Format3 0: normal speed, 1: high speed Root Sequence Cyclic Shift per Use Zero Correlation Zone (Ncs value 59)
Retrans Num
Retransmit number
Tx Power
RACH transmit power
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Timing Adjustment Info Tx Timing adjustment log shows the TA position.
Parameter
Description
Rx SFN
Received frame number
Rx TTI
Received subframe number
NTA NTA
Timing advance command In case of random access response : 11bit for NTA NTA In other case : 6bit for NTA (TA (TA = 0, 1, 2,..., 63)
Accum TA
Accumulate Accumulate timing timing advance advance command command
Cell Info Cell Information display cell lists which are collected from Mp Searcher and Cell Searcher.
Parameter
Description
INTRA>SYNC> RSRP
Reference Signal Received Power of Intra cell which is known the sync position.
INTRA>SYNC> RSRQ
Reference Signal Received Quality of Intra cell which is known the sync position
INTRA>SYNC> RSSI
Received Power of Intra cell which is known the sync position
INTRA>SYNC> FrameBound INTRA>SYNC> CPLength
Cell frame boundary in Intra Sync CP length in Intra Sync 0: Unknown 1 : Normal CP 2 : Extended CP
INTRA>SYNC> DL Earfcn INTRA>SYNC> Top Set
INTRA>ASYNC> RSRP INTRA> ASYNC> RSRQ INTRA> ASYNC> RSSI INTRA> ASYNC> FrameBound
© Copyright by Accuver Ltd.
Earfcn number in Intra Sync PCI
PCI with RSRP strength from top 1 to 20 from Intra Sync Cell
RSRP
Top 1 to 20 RSRP from Intra Sync Cell
RSRQ
Top 1 to 20 RSRQ from Intra Sync Cell
RSSI
Top 1 to 20 RSSI from Intra Sync Cell
FrameBound
Top 1 to 20 FrameBound from Intra Sync Cell
CPLength
Top 1 to 20 CPLength from Intra Sync Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Intra Sync Cell
Reference Signal Received Power of Intra cell which is unknown the sync position. Reference Signal Received Quality of Intra cell which is unknown the sync position Received Power of Intra cell which is unknown the sync position Cell frame boundary in Intra Async
Page 3
INTRA> ASYNC> CPLength
CP length in Intra Async 0: Unknown 1 : Normal CP 2 : Extended CP
INTRA> ASYNC> DL Earfcn INTRA> ASYNC > Top Set
INTRA>DETECT> RSRP INTRA> DETECT> RSRQ INTRA> ASYNC> RSSI INTRA> DETECT> FrameBound INTRA> DETECT> CPLength
Earfcn number in Intra Async PCI
PCI with RSRP strength from top 1 to 20 from Intra Async Cell
RSRP
Top 1 to 20 RSRP from Intra Async Cell
RSRQ
Top 1 to 20 RSRQ from Intra Async Cell
RSSI
Top 1 to 20 RSSI from Intra Async Cell
FrameBound
Top 1 to 20 FrameBound from Intra Async Cell
CPLength
Top 1 to 20 CPLength from Intra Async Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Intra Async Cell
Reference Signal Received Power of Intra cell which is newly detected at this search. Reference Signal Received Quality of Intra cell which is newly detected at this search Received Power of Intra cell which is newly detected at this search Cell frame boundary in Intra Detected CP length in Intra Detected 0: Unknown 1 : Normal CP 2 : Extended CP
INTRA> DETECT> DL Earfcn INTRA> DETECT > Top Set
Earfcn number in Intra Detected PCI
PCI with RSRP strength from top 1 to 20 from Intra Detect Cell
RSRP
Top 1 to 20 RSRP from Intra Detect Cell
RSRQ
Top 1 to 20 RSRQ from Intra Detect Cell
RSSI
Top 1 to 20 RSSI from Intra Detect Cell
FrameBound
Top 1 to 20 FrameBound from Intra Detect Cell
CPLength
Top 1 to 20 CPLength from Intra Detect Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Intra Detect Cell
INTER>SYNC> RSRP
Reference Signal Received Power of Inter cell which is known the sync position.
INTER>SYNC> RSRQ
Reference Signal Received Quality of Inter cell which is known the sync position
INTER>SYNC> RSSI
Received Power of Inter cell which is known the sync position
INTER>SYNC> FrameBound
Cell frame boundary in Inter Sync
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
INTER>SYNC> CPLength
CP length in Inter Sync 0: Unknown 1 : Normal CP 2 : Extended CP
INTER>SYNC> DL Earfcn INTER >SYNC> Top Set
INTER>ASYNC> RSRP INTER> ASYNC> RSRQ INTER> ASYNC> RSSI INTER> ASYNC> FrameBound INTER> ASYNC> CPLength
Earfcn number in Inter Sync PCI
PCI with RSRP strength from top 1 to 20 from Inter Sync Cell
RSRP
Top 1 to 20 RSRP from Inter Sync Cell
RSRQ
Top 1 to 20 RSRQ from Inter Sync Cell
RSSI
Top 1 to 20 RSSI from Inter Sync Cell
FrameBound
Top 1 to 20 FrameBound from Inter Sync Cell
CPLength
Top 1 to 20 CPLength from Inter Sync Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Inter Sync Cell
Reference Signal Received Power of Inter cell which is unknown the sync position. Reference Signal Received Quality of Inter cell which is unknown the sync position Received Power of Inter cell which is unknown the sync position Cell frame boundary in Inter Async CP length in Inter Async 0: Unknown 1 : Normal CP 2 : Extended CP
INTER> ASYNC> DL Earfcn INTER > ASYNC > Top Set
INTER>DETECT> RSRP INTER> DETECT> RSRQ INTER> ASYNC> RSSI INTER> DETECT> FrameBound
© Copyright by Accuver Ltd.
Earfcn number in Inter Async PCI
PCI with RSRP strength from top 1 to 20 from Inter Async Cell
RSRP
Top 1 to 20 RSRP from Inter Async Cell
RSRQ
Top 1 to 20 RSRQ from Inter Async Cell
RSSI
Top 1 to 20 RSSI from Inter Async Cell
FrameBound
Top 1 to 20 FrameBound from Inter Async Cell
CPLength
Top 1 to 20 CPLength from Inter Async Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Inter Async Cell
Reference Signal Received Power of Inter cell which is newly detected at this search. Reference Signal Received Quality of Inter cell which is newly detected at this search Received Power of Inter cell which is newly detected at this search Cell frame boundary in Inter Detected
Page 5
INTER> DETECT> CPLength
CP length in Inter Detected 0: Unknown 1 : Normal CP 2 : Extended CP
INTER> DETECT> DL Earfcn INTER > DETECT > Top Set
Earfcn number in Inter Detected PCI
PCI with RSRP strength from top 1 to 20 from Inter Detect Cell
RSRP
Top 1 to 20 RSRP from Inter Detect Cell
RSRQ
Top 1 to 20 RSRQ from Inter Detect Cell
RSSI
Top 1 to 20 RSSI from Inter Detect Cell
FrameBound
Top 1 to 20 FrameBound from Inter Detect Cell
CPLength
Top 1 to 20 CPLength from Inter Detect Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Inter Detect Cell
All Set
All Cell Cell RSRP/RSR RSRP/RSRQ/RS Q/RSSI/Fram SI/FrameBound eBound /CPLength/DL /CPLength/DL Earfcn/Cell Earfcn/Cell State State per PCI
Top Set
PCI
PCI with RSRP strength from top 1 to 20 from All Cell
RSRP
Top 1 to 20 RSRP from All Cell
RSRQ
Top 1 to 20 RSRQ from All Cell
RSSI
Top 1 to 20 RSSI from All Cell
FrameBound
Top 1 to 20 FrameBound from All Cell
CPLength
Top 1 to 20 CPLength from All Cell
DL Earfcn
Top 1 to 20 DL Earfcn from All Cell Top 1 to 20 Cell State from All Cell - Intra Sync - Intra Async
Cell State
- Intra Detect - Inter Sync - Inter Async - Inter Detect
Search Result Search Result log shows Mp Search result and Cell Search result.
Parameter MP Searcher
Description Mp Searcher Dominant Energy and Mp Searcher position per PCIS (PCIS: 0,1 or 2)
Cell Searcher> Dominant PCI
PCI with Dominant Cell Search Energy
Cell Searcher> Dominant Cell Srch Energy
Dominant Cell Search Energy
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Cell Searcher> PCI#
Cell Search Energy, Energy, PCIG, PCIG, Half Frame Idx and CP Length per PCI (PCIG: 0 ~ 167, PCI: 0 ~ 503)
Earfcn Used Cell Searcher Num
EARFCN number Num of Used Cell Searcher
Channel Info The channel information shows no antenna in the 2x2 MIMO channel.
Parameter Tx Correlation> Freq Total Band(Avg) Tx Correlation> Freq Sub Band x Rx Correlation> Freq Total Band(Avg) Rx Correlation> Freq Sub Band x H00 (Real)> Freq Sub Band x H00 (Imaginary)> Freq Sub Band x H01 (Real)> Freq Sub Band x H01 (Imaginary)> Freq Sub Band x H10 (Real)> Freq Sub Band x H10 (Imaginary)> Freq Sub Band x H11 H11 (Real)> Freq Sub Band x H11 H11 (Imaginary)> Freq Sub Band x
Description Tx Correlation in Total Band(Sub Band 1 ~ 30)
Tx Correlation per Sub Band
Rx Correlation in Total Band(Sub Band 1 ~ 30)
Tx Correlation per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
CQI Info The wideband CQI information shows measured CQI of wideband in the UE. The sub-band CQI information shows the CQI (channel quality information) of sub-bands. The sub-band is defined a unit for a group of resource elements used for reporting sub-band CQI.
Parameter Rank Ratio> Instant
© Copyright by Accuver Ltd.
Description Instant Rank Ratio (Range 0 ~ 1)
Page 7
Rank Ratio> Cumulative CQI(Wideband)> Rank1 CQI CQI(Wideband)> Rank2 CW0 CQI CQI(Wideband)> Rank2 CW1 CQI CQI(Wideband)> Rank1 PMI CQI(Wideband)> Rank2 PMI CQI(Subband)> Rank1 CQI CQI(Subband)> Rank2 CW0 CQI CQI(Subband)> Rank2 CW1 CQI CQI(Subband)> Rank1 PMI CQI(Subband)> Rank2 PMI
Cumulative Rank Ratio (Range 0 ~ 1) Rank1 wide band CQI
Rank2 wide band CQI for CW0
Rank2 wide band CQI for CW1
Rank1 wide band PMI
Rank2 wide band PMI
Rank1 sub band CQI
Rank2 sub band CQI for CW0
Rank2 sub band CQI for CW1
Rank1 sub band PMI
Rank2 sub band PMI
Multi-paths Profile This information shows the channel impulse response of reference signals in the time domain.
Parameter Serving PCI Ref EsNo
Description Serving cell ID (0~503) The reference EsNo is the detected RS SNR in the reference position. RS power metric of reference path. EsNo is calculated by computing 10*log10(RS power metric/noise power metric)
Ref Timing
The reference timing gives the information of reference cell timing of demodulation. Reference timing of serving cell. The resolution is Ts in a frame
Path Info[x]> EsNo Path Info[x]> Time Index
RS power metric of this path Timing offset from reference timing t iming (Ts (Ts resolution)
PBCH BLER PBCH BLER displays how much transport blocks get CRC_NOK about total received transport blocks.
Parameter Instant
Description Instant PBCH BLER (bler_info.err_nums / bler_info.total_nums) * 100
Cumulative
Cumulative PBCH BLER
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
PDSCH BLER PDSCH BLER displays how much transport blocks get CRC_NOK CRC_NOK about total received transport blocks.
Parameter Instant> All Instant> All
Description Instant Instant PDSCH PDSCH Total BLER BLER ((bler_info[0].err_nums + bler_info[1].err_nums) / (bler_info[0].total_nums + bler_info[1].total_nums)) * 100
Instant> Codeword #0
Instant PDSCH Codeword0 BLER (bler_info[0].err_nums / bler_info[0].total_nums) * 100
Instant> Codeword #1
Instant PDSCH Codeword1 BLER (bler_info[1].err_nums / bler_info[1].total_nums) * 100
Cumulative> All Cumulative> All Cumulative> Codeword #0 Cumulative> Codeword #1
Cumulative PDSCH Total BLER Cumulative PDSCH Codeword0 BLER
Cumulative PDSCH Codeword1 BLER
PDCCH Detection Rate UE can’t calculate PDCCH BLER because UE doesn’t know when eNode -B sends its PDCCH. In other
words, UE detects PDCCH blindly. So, UE DM supports this item similar with PDCCH BLER.
Parameter
Description
DCI 0
The number of detection for DCI#0
DCI 1
The number of detection for DCI 1
DCI 1a
The number of detection for DCI 1a
DCI 1b
The number of detection for DCI 1b
DCI 1c
The number of detection for DCI 1c
DCI 2
The number of detection for DCI 2
DCI 2a
The number of detection for DCI 2a
DCI 3
The number of detection for DCI 3
DCI 3a
The number of detection for DCI 3a
DL Grant & UL Ack/Nack Status Info(Improved) DL Grant & UL ACK/NACK Status(Improved) Status(Improved) displays DL grant regardless any DCI format fo rmat in every TTI. According According to TS36.212, TS36.212, each each DCI DCI format format has the the specific specific fields, fields, not all, all, and the the unnecessa unnecessary ry fields fields are are displayed to the blank. Additionally, UL_ACK/NACK, CFI, and DCI_3/3A payload will be included in this item.
Parameter SFN
© Copyright by Accuver Ltd.
Description SFN value
Page 9
TTI DCI Format> Count
TTI value DCI 1 Num/ DCI 1A Num/ DCI 1B Num/ DCI 1C Num/ DCI 2 Num/ DCI 2A Num/ DCI 3 Num/ DCI 3A Num/ N/A Num
DCI Format> Rate
DCI 1 Rate/ DCI 1A Rate/ DCI 1B Rate/ DCI 1C Rate/ DCI 2 Rate/ DCI 2A Rate/ DCI 3 Rate/ DCI 3A Rate/ N/A Rate
TM Scheme
transmission scheme 0:"SING-ANT(P0)",1:"SING-ANT(P5)",2:"TRANSDIV",3:"LARGE-CDD",4:"CLOSE-SM",5:"MU-MIMO"
TPC RB Num MCS> CW0> MCS(Idx) MCS> CW0> QPSK Rate MCS> CW0> 16 QAM Rate MCS> CW0> 64 QAM Rate MCS> CW1> MCS(Idx) MCS> CW1> QPSK Rate MCS> CW1> 16 QAM Rate MCS> CW1> 64 QAM Rate NDI> CW0> New Data Num NDI> CW0> Retrans Data Num NDI> CW0> New Data Rate NDI> CW1> New Data Num NDI> CW1> Retrans Data Num NDI> CW1> New Data Rate UL ACK/NACK> CW0> ACK Count Count UL ACK/NACK> CW0> NACK Count UL ACK/NACK> CW0> DTX Count
TPC Resource Block Number CW0 MCS CW0 QPSK Rate
CW0 16 QAM Rate
CW0 64 QAM Rate CW1 MCS CW1 QPSK Rate
CW1 16 QAM Rate
CW1 64 QAM Rate
CW0 NDI (NDI field = 1)
CW0 NDI (NDI field = 0)
New Data Num/(Retrans Data Num+New Data Num)*100 in CW0
CW1 NDI (NDI field = 1)
CW1 NDI (NDI field = 0)
New Data Num/(Retrans Data Num+New Data Num)*100 in CW1
CW0 UL ACK result
CW0 UL NACK result
CW0 UL DTX result
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
UL ACK/NACK> CW0> ACK Rate Rate UL ACK/NACK> CW0> NACK Rate UL ACK/NACK> CW0> DTX Rate UL ACK/NACK> CW1> ACK Count Count UL ACK/NACK> CW1> NACK Count UL ACK/NACK> CW1> DTX Count UL ACK/NACK> CW1> ACK Rate Rate UL ACK/NACK> CW1> NACK Rate UL ACK/NACK> CW1> DTX Rate DCI 3(Mode)> DCI 3/3A Value(CW0) DCI 3(Mode)> DCI 3/3A Value(CW1)
ACK Count/(ACK Count/(ACK Count+N Count+NACK ACK Count+D Count+DTX TX Count)*10 Count)*100 0 in CW0
NACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
DTX Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
CW1 UL ACK result
CW1 UL NACK result
CW1 UL DTX result
ACK Count/(ACK Count/(ACK Count+N Count+NACK ACK Count+D Count+DTX TX Count)*10 Count)*100 0 in CW1
NACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
DTX Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
CW0 DCI3/3A value
CW1 DCI3/3A value
DL Grant & UL Ack/Nack Status Info(Improved)[Detail per TTI] DL Grant & UL Ack/Nack Status Status Info(Improved)[Detail per pe r TTI] displays the related information per TTI.
Parameter
Description
SFN
SFN value
TTI
TTI value
CFI
CFI value
DCI Format
DCI format 0:"DCI_1",1:"DCI_1A,2:"DCI_1B",3:"DCI_1C",4:"DCI_2", 5:"DCI_2A",6:"DCI_3",7:"DCI_3A"
RNTI
RNTI type 0:"C-RNTI",1:"RA-RNTI",2:"P-RNTI",3:"SI-RNTI", 0:"C-RNTI",1:"RA-RNTI",2:"PRNTI",3:"SI-RNTI", 4:"PUCCH",5:"PUSCH",6:"S 4:"PUCCH",5:"PUSCH",6:"SPSPSRNTI",7:”T-CRNTI”
TM Scheme
transmission scheme 0:"SING-ANT(P0)",1:"SING-ANT(P5)",2:"TRANS0:"SING-ANT(P0)",1:"SING -ANT(P5)",2:"TRANS- DIV",3:"LARGE-CDD",4:"CLO DIV",3:"LARGE-CDD",4:"CLOSESESM",5:"MU-MIMO"
Distribution Flag
distribution flag 0:"LOCAL", 1:"DIST"
Gap Value
gap value
RA Header
RA header
© Copyright by Accuver Ltd.
Page 11
Precoding RB Num PMI Confirmation TPC HARQ Number
precoding information Resource Block Number PMI confirmation TPC HARQ number
MCS(CW0)
MCS in CW0
NDI(CW0)
NDI in CW0
RV(CW0)
redundancy version in CW0
MOD Type(CW0) New/Retrans Type(CW0) TB Size(CW0) CRC Result(CW0) UL ACK/NACK Result(CW0)
modulation type in CW0 new or retransmission type in CW0 transport block size in CW0 CRC result in CW0 UL ACK/NACK ACK/NACK result in CW0
DCI 3(CW0)
DCI3/3A value in CW0
MCS(CW1)
MCS in CW1
NDI(CW1)
NDI in CW1
RV(CW1)
redundancy version in CW1
MOD Type(CW1) New/Retrans Type(CW1) TB Size(CW1) CRC Result(CW1) UL ACK/NACK Result(CW1) DCI 3(CW1)
modulation type in CW1 new or retransmission type in CW1 transport block size in CW1 CRC result in CW1 UL ACK/NACK ACK/NACK result in CW1 DCI3/3A value in CW1
UL Grant & DL Ack/Nack Status Info UL Grant Info Status log shows get UL Scheduling Grant information to PDCCH.
Parameter
Description
SFN
SFN value
TTI
TTI value
FH> FH Num FH> No FH Num FH> FH Rate MCS> CQI REQ> MCS(Idx) MCS> No CQI REQ> MCS(Idx)
FH Number No FH Number FH Num/(No FH Num+FH Num)* 100 No CQI Request Modulation and Coding Rate
CQI Request Modulation and Coding Rate
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
MCS> No CQI REQ> QPSK Rate MCS> No CQI REQ> 16 QAM Rate MCS> No CQI REQ> 64 QAM Rate
QPSK Num/(QPSK Num+16QAM Num+64QAM Num)*100 in CQI Request
16QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in CQI Request
64QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in CQI Request
New Data Num
New data indicator (NDI field = 1)
Retrans Data Num
New data indicator (NDI field = 0)
New Data Rate TPC CS DMRS DL ACK/NACK> ACK Count DL ACK/NACK> NACK Count DL ACK/NACK> DTX Count DL ACK/NACK> ACK ACK/NACK> ACK Rate DL ACK/NACK> NACK Rate DL ACK/NACK> DTX Rate
New Data Num/(Retrans Data Num+New Data Num)*100 Power control of PUSCH Cyclic shift for DMRS DL ACK result
DL NACK result
DL DTX result
ACK Count/(ACK Count/(ACK Count+N Count+NACK ACK Count+D Count+DTX TX Count)*10 Count)*100 0
NACK Count/(ACK Count+NACK Count+DTX Count)*100
DTX Count/(ACK Count+NACK Count+DTX Count)*100
UL Grant & DL Ack/Nack Status info[Detail per TTI] UL Grant & DL Ack/Nack Status info[Detail per TTI] displays the related information per TTI.
Parameter
Description
SFN
SFN value
TTI
TTI value
TB Size RB Assign FH
Transport Block size Resurce block assingment 0 :No FH 1 :FH
MCS
Modulation and Coding Rate
NDI
New data indicator
TPC
Power control of PUSCH
CS DMRS CQI Request Ind
Cyclic shift for DMRS CQI Request Indication 0 : No CQI Request 1 : CQI Request
© Copyright by Accuver Ltd.
Page 13
DL ACK/NACK Result
0 :NACK 1 :ACK
PDSCH PHY Throughput PDSCH PHY Throughput has displays how much to get the downlink data in 1sec.
Parameter All
Description PDSCH PDSCH PHY Total Throughput Throughput (cw_0 + cw_1) / 1000
Codeword #0
PDSCH PHY Codeword0 Throughput (cw_0) / 1000
Codeword #1
PDSCH PHY Codeword0 Throughput (cw_1) / 1000
UL PRB MAP Data Info This information shows the log of transmit physical resource mapping information.
Parameter
Description
SFN
Frame number
TTI
TTI number
Bandwidth
0:1.4MHz, 1:3MHz, 2:5MHz, 3:10MHz, 4:15MHz, 5:20MHz
Channel Type> Count
DTX/ PRACH/ PUCCH/ PUSCH/ SRS/ PUSCH+SRS/ PUCCH+SRS Count
Channel Type> Rate
DTX/ PRACH/ PUCCH/ PUSCH/ SRS/ PUSCH+SRS/ PUCCH+SRS Rate
PRACH
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PRACH
PUCCH
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUCCH
PUSCH
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUSCH
SRS
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in SRS
PUSCH+SRS
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUSCH+SRS
PUCCH+SRS
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUCCH+SRS
PUSCH PHY Throughput UL Throughput log shows the Uplink data throughput at UE side.
Parameter NEW Transmission
Description A number of bits about new transmission per 1 sec (new_bit_nums) / 1000
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Total UL
A number of bits about re-transmission per 1 sec (new_bit_nums + retrans_bit_nums) / 1000
L2 DL Throughput Parameter PDCP> Total
Description Total Downlink Downli nk PDCP Throughput Throug hput (∑rbId total Byte*8/1000)
PDCP> RB ID(x)
Downlink PDCP Throughput per RB ID (rbId total Byte*8/1000)
RLC> Total
Total Downlink RLC Throughput (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM), 4 ~ 5 (UM)
RLC> AM> RLC> AM> Total
Total Downlink Downlink RLC AM Throughpu Throughputt (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> AM> RLC> AM> RB RB ID(x) ID(x)
Downlink Downlink RLC RLC AM Throughpu Throughputt per RB RB ID (rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> UM> Total
Total Downlink Downli nk RLC UM Throughput Throug hput (∑rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
RLC> UM> RB ID(x)
Downlink RLC UM Throughput per RB ID (rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
MAC
Downlink MAC Throughput (MacDlTotalBytes*8/1000)
L2 UL Throughput Parameter PDCP> Total
Description Total Uplink Uplin k PDCP Throughput Throug hput (∑rbId total Byte*8/1000)
PDCP> RB ID(x)
Uplink PDCP Throughput per RB ID (rbId total Byte*8/1000)
RLC> Total
Total Uplink Uplin k RLC Throughput Throug hput (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM), 4 ~ 5 (UM)
RLC> AM> RLC> AM> Total
Total Uplink Uplink RLC RLC AM Throughpu Throughputt (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
© Copyright by Accuver Ltd.
Page 15
RLC> AM> RLC> AM> RB RB ID(x) ID(x)
Uplink RLC AM Throughput Throughput per RB ID (rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> UM> Total
Total Uplink Uplin k RLC UM Throughput Throug hput (∑rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
RLC> UM> RB ID(x)
Uplink RLC UM Throughput per RB ID (rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
MAC
Uplink MAC Throughput (MacUlTotalBytes*8/1000)
PDSCH MAC BLER This item is for MAC BLER of downlink (PDSCH). Ratio of transport blocks which remain unacknowledged (CRC failure) after HARQ retransmission divided by total number of initial transmissions received by UE MAC
Parameter Instant> All Instant> All
Description Instant Instant total total MAC MAC BLER ( (cwd0ErrNum/cwd0TBNum) *100 + (cwd1ErrNum/cwd1TBNum) *100 ) / 2
Instant> Codeword #0
Instant code word #0 MAC BLER (cwd0ErrNum/cwd0TBNum) *100
Instant> Codeword #1
Instant code word #1 MAC BLER (cwd1ErrNum/cwd1TBNum) *100
Cumulative> All Cumulative> All Cumulative> Codeword #0 Cumulative> Codeword #1
Cumulative total MAC BLER Cumulative code word #0 MAC BLER
Cumulative code word #1 MAC BLER
RLC States Info This item provides state information of RLC Tx/Rx Entity.
Parameter Tx States> RB ID (x)> Mode Tx States> RB ID (x)> State Rx States> RB ID (x)> Mode Rx States> RB ID (x)> State
Description Tx States RLC Mode (AM /UM/TM)
Tx States RLC Tx Entity state (NULL/DTR)
Rx States RLC Mode (AM /UM/TM)
Rx States RLC Tx Entity state (NULL/DTR)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
MAC State Info This item includes MAC DL/UL state information.
Parameter MAC UL State
Description Current state of MAC uplink (0-NOT_CONFIGURED, (0-NOT_CONFIGURED, 1-CONFIGURED, 2-OUT_OF_SYNC, 3-IN_SYNC, 44IN_CR, 5-READY_TO_SCHED )
MAC DL State
Current State of MAC downlink (0-NOT_CONFIGURED, 1-CONFIGURED, 2-PCH_STATE, 3-RACH_STATE, 4DSCH_STATE)
MAC UL Transmission Info This item is for total packets information of uplink data transmission.
Parameter Count> 1st Trans
Description Success in 1st transmission
Count> 1st Re-Trans
Success in 1st re-transmission
Count> 2nd Re-Trans
Success in 2nd re-transmission
Count> 3rd Re-Trans
Success in 3rd re-transmission
Count> 4th Re-Trans
Success in 4th re-transmission
Count> 5th Re-Trans
Success in 5th re-transmission
Count> 6th Re-Trans
Success in 6th re-transmission
Count> 7th Re-Trans
Success in 7th re-transmission
Count> 8th Re-Trans
Success in 8th re-transmission
Count> 9th Re-Trans
Success in 9th re-transmission
Count> 10th Re-Trans
Success in 10th re-transmission
Count> Total Trans
∑SuccessCnt i (Where, i = 0 to 10)
Count> Bad Count
Bad Count
Percentage> 1st Trans Percentage> 1st ReTrans Percentage> 2nd ReTrans Percentage> 3rd ReTrans Percentage> 4th ReTrans Percentage> 5th ReTrans
© Copyright by Accuver Ltd.
1st Trans/(Total Trans/(Total Trans+Bad Count)*100 1st Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
2nd Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
3rd Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
4th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
5th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
Page 17
Percentage> 6th ReTrans Percentage> 7th ReTrans Percentage> 8th ReTrans Percentage> 9th ReTrans Percentage> 10th ReTrans Percentage> Total Trans Percentage> Bad Percentage
6th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
7th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
8th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
9th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
10th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100 Total Trans/(Total Trans+Bad Count)*100 Bad Count/(Total Trans+Bad Count)*100
RACH REQ Info This item includes RACH request information.
Parameter
Description
RACH Transmit Time
RACH transmit time
Retransmission Num
Retransmission Num
RACH Type
0 : INITIAL 1 : HANDOVER 2 : UL DATA ARRIVAL 3 : DL DATA ARRIVAL 4 : SR MAX 5 : NO_SR_CONFIG
RA-RNTI Preamble ID
RACH RNTI Preamble Identity
RACH RSP General Info This item includes RACH response information.
Parameter RACH Response Receiving Time Result RACH Preamble Identity BackOff Indicator Time Advance Temporary C-RNTI MCS
Description RACH response receiving time 0: NACK, 1: ACK RACH Preamble Identity BackOff Indicator Time Advance Temporary C-RNTI Modulation and coding Scheme
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
TPC for scheduled PUSCH Hopping Flag UL Delay CQI Request Resource Block Assignment Assignment Access Access RACH RACH Latency Latency
TPC command for scheduled PUSCH Hopping Flag UL Delay CQI Request Resource block assignment(10bits) Access Access RACH RACH Latency Latency (sec) (sec)
RNTI Info This item includes RNTI information.
Parameter C-RNTI RA-RNTI Temporary empora ry C-RNTI
Description C-RNTI RA-RNTI Temporary empor ary C-RNTI
Serving Cell & Neighbor Cell Lists Parameter Serving Cell Info> UE State
Description Current UE state - UE_IDLE_MODE - UE_CONNECTED_MODE UE_CONNECTED_MODE - NO_SERVICE - NON_LTE_RAN
Serving Cell Info> Freq UL Serving Cell Info> Freq DL
Uplink Carrier Frequency
Downlink Carrier Frequency
Serving Cell Info> PCI
Physical Cell Identity
Serving Cell Info> TAC
Tracking Area Code
Serving Cell Info> PLMN Identity Serving Cell Info> Global Cell ID Intra Freq Cell Lists> DL Freq
PLMN Identity
Global Cell ID
Downlink Carrier Frequency
Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving PCI
PCI
© Copyright by Accuver Ltd.
Page 19
Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving RSRP
RSRP Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving RSRQ
RSRQ Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving RSSI
RSSI Intra Freq Cell Lists> Serving Cell> All Cell> All Cell Cell
Intra Freq Cell Serving RSRP/RSSQ/RSSI per PCI
Info Intra Freq Cell Lists> Monitored Cell>
Number of Monitored PCI from Intra Freq Cell
Monitored Cell Count Intra Freq Cell Lists> Monitored Cell>
Monitored PCI List from Intra Freq Cell
Monitored Cell List Intra Freq Cell Lists> Monitored Cell> Summary Monitored
Monitored PCI List with (RSRP,RSRQ) (RSRP,RSRQ) from Intra Freq Cell
Cell List Intra Freq Cell Lists> Monitored Cell> RSRP Intra Freq Cell Lists> Monitored Cell> RSRQ Intra Freq Cell Lists> Monitored Cell> RSSI Intra Freq Cell Lists> Monitored Cell> Top Set
Intra Freq Cell Monitored RSRP per PCI
Intra Freq Cell Monitored RSRQ per PCI
Intra Freq Cell Monitored RSSI per PCI PCI
PCI with RSRP strength from top 1 to 20 from Intra Freq Monitored Cell
RSRP
Top 1 to 20 RSRP from Intra Freq Monitored Cell
RSRQ
Top 1 to 20 RSRQ from Intra Freq Monitored Cell
RSSI
Top 1 to 20 RSSI from Intra Freq Monitored Cell
Intra Freq Cell Lists> Detected Cell> Detected
Number of Detected PCI from Intra Freq Cell
Cell Count Intra Freq Cell Lists> Detected Cell> Detected
Detected PCI List from Intra Freq Cell
Cell List Intra Freq Cell Lists> Detected Cell> Summary Detected Cell List
Detected PCI List with (RSRP,RSRQ) (RSRP,RSRQ) from Intra Freq Cell
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Intra Freq Cell Lists> Detected Cell> RSRP Intra Freq Cell Lists> Detected Cell> RSRQ Intra Freq Cell Lists> Detected Cell> RSSI Intra Freq Cell Lists> Detected Cell> Top Set
Intra Freq Cell Lists> Lists> All All Set Intra Freq Cell Lists> Top Set
Intra Freq Cell Detected RSRP per PCI
Intra Freq Cell Detected RSRQ per PCI
Intra Freq Cell Detected RSSI per PCI PCI
PCI with RSRP strength from top 1 to 20 from Intra Freq Detected Cell
RSRP
Top 1 to 20 RSRP from Intra Freq Detected Cell
RSRQ
Top 1 to 20 RSRQ from Intra Freq Detected Cell
RSSI
Top 1 to 20 RSSI from Intra Freq Detected Cell
Intra Freq Cell RSRP/RSRQ/RSSI/C RSRP/RSRQ/RSSI/Cell ell State per PCI PCI
PCI with RSRP strength from top 1 to 20 from Intra Freq Cell
RSRP
Top 1 to 20 RSRP from Intra Freq Cell
RSRQ
Top 1 to 20 RSRQ from Intra Freq Cell
RSSI
Top 1 to 20 RSSI from Intra Freq Cell Top 1 to 20 Cell State from Intra Freq Cell
Cell State
- Serving - Monitored - Detected
Inter Freq Cell Lists> Freq DL(x)>PCI(y)>
Inter frequency cell Reference Signal Received Power
RSRP Inter Freq Cell Lists> Freq DL(x)>PCI(y)>
Inter frequency cell Reference Signal Received Quality
RSRQ Inter Freq Cell Lists> Freq DL(x)>PCI(y)>
Inter frequency cell Received Power
RSSI Inter Freq Cell Lists> Freq DL(x)>PCI(y)> Cell Type
Inter frequency cell type 1 : monitored cell 2 : detected cell
NAS System Info Parameter PLMN_ID TAC
Description PLMN ID of the current cell TAC of the current cell
Cell ID
Cell ID of the current cell
TAI List
Tracking Area identity List MCC (Mobile Country Code), MNC (Mobile Network Code) and TAC (Tracking (Tracking Area Code).
© Copyright by Accuver Ltd.
Page 21
RRC BCH Status Info This item provides the information of BCH status.
Parameter
Description
RRC BCH Status> PCI
Physical Cell Identity (0~503)
RRC BCH Status> Freq DL
DL Frequency
RRC BCH Status> Purpose
Purpose of BCH Setup - SIB_NORMAL, - CELL_RESELECTION, - SIB_MODIFICATION, - MOVE_TO_IDLE, MOVE_TO_IDLE, - SIB_CONNECTED, - SFN_READ, - SPECIFIED_SIB, - SIBC_SIB
RRC BCH Status> Result
Result of receiving System Information. - SUCCESS, - PLMN_MISMATCH, - MIB_TIMEOUT, - SI_TIMEOUT, - LAST_RESULT
NAS State Info This item provides the state information of EMM (EPS Mobility Management), ECM (EPS Connection Management) and PLMN and EU (EPS Update) status when each state is changed.
Parameter
Description
EMM State
Current state of EMM (EPS Mobility Management)
ECM State
Current state of ECM (EPS Connection Management)
PLMN State
Current state of PLMN
EU State
Current EU (EPS Update) status
NAS State Info(R4) This item provides the NAS state information of EMM (EPS Mobility Management), ECM (EPS Connection Management) and PLMN and EMM Cache status when each state is changed.
Parameter
Description
EMM State
Current state of EMM (EPS Mobility Management)
ECM State
Current state of ECM (EPS Connection Management)
PLMN State
Current state of PLMN
EMM Cache State
Current state of EMM Cache
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Radio & NAS Signaling Failure Info Parameter Radio Problem Cause NAS Signaling Failure Cause
Description Radio problem diagnostic logging attribute. NAS signaling failure diagnostic logging attribute
RRC Freq Scan Info This item displays the result of frequency scan.
Parameter Search Type Type
Description Cell Search Method - Frequency LIST - Frequency RANGE
Freq DL RSRP
DL Frequency Reference Signal Received Power
Cell Reselection Info This item provides the information on both source cell and target cell when RRC perform cell reselection.
Parameter Old Freq DL Old Cell ID New Freq DL New Cell ID
Description Old Carrier Frequency Old Cell Identity New Carrier Frequency New Cell Identity
Handover History This item displays handover history, delay and result.
Parameter
Description
Source Cell
Source Cell Physical Identity
Target Cell
Target Cell Physical Identity
Handover Delay
Handover delay (Unit : ms)
Result
- FAIL - SUCCESS
Handover Hando ver Type
- LTE - Outbound IRA I RAT T - Inbound IRAT IRAT
© Copyright by Accuver Ltd.
Page 23
Data Path Packet Loss This item is for UL/DL packet loss of data path(HIM/PDCP/L2).
Parameter
Description
UL UsbBlockTime
UL : USB Blocking count
UL SdioBlockTime
UL : SDIO Blocking count
UL UsbUnreg
UL : number of discarded packet in USB by unregistered connection
UL SdioUnreg
UL : number of discarded packet in SDIO by unregistered connection
UL HimAllocFail
UL : Memory allocation fail count in HIM
UL DimInvHdr
UL : Number of discarded packet in DIM by Invalid header
UL DimNoRB
UL : Number of discarded packet in DIM because of no RB
UL PdcpSduFull
UL : Fail count in PDCP by PDCP SDU Queue full
UL PdcpPduBufFull
UL : Number of discarded packet in PDCP by PDCP PDU Queue full
UL PdcpCipAllocFail
UL : Number of discarded packet in PDCP by Ciphering block full
UL PdcpDisTimer
UL : Number of discarded packet by PDCP discard timer expiry
UL MacSchedMiss
UL : Number of discarded MAC PDU which is not transfered
DL PhyAllocFail DL MacInvHdr DL RlcDuplication DL RlcInvHdr
DL : Number of discarded MAC PDU by memory allocation in L1 DL : Number of discarded MAC PDU by invalid MAC header DL : number of discarded RLC PDU by duplication DL : number of discarded RLC PDU by invalid RLC header
DL RlcOutWnd
DL: number of discarded RLC PDU which falls outside of window
DL RlcRsmFull
DL : number of discard RLC PDU by RSM buffer full
DL PdcpInvHdr
DL : number of discarded PDCP PDU by invalid PDCP header
DL PdcpOutWnd DL CipAllocFail DL DimInvalid DL HimIfFull
DL : number of discarded PDCP PDU which falls outside of window DL : Number of discarded packet in PDCP by Ciphering block full DL : Number of discarded packet in DIM by IP Header length mismatch DL : Number of discarded packet in HIM by interface buffer full
DL UsbBlockTime
DL : USB block count
DL SdioBlockTime
DL : SDIO block count
DL UsbPacketLoss
DL : number of discarded packet in USB
DL SdioPacketLoss
DL : number of discard packet in SDIO
ESM Instance Info This item includes ESM instance information R3. Maximum number of ESM instance is 15(1~15). The EPS Id uniquely identifies each ESM instance.
Parameter Tab Index EPS Id Linked Bearer Id
Description st
nd
1: 1 tab, 2: 2 EPS ID
Linked Bearer ID
tab, … 15: 15
th
tab
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
PDN Address APN QCI EPS Type
PDN IP Address Access Access Point Name QCI (1 ~ 9) - NONE BEARER TYPE - DEFAULT_BEARER - DEDICATED_BEARER
ESM State
- DEACTIVE - ACTIVE
PTI Instance Id Deactivate Mode
PTI Instance ID - NONE_MODE - NORMAL - NORMAL_ALL - DETACH - STATUS_IND - PDN_DISCONNECT - PDN_DISCONNECT_REJECT PDN_DISCONNECT_REJECT - PDN_DISCONNECT_TIMEOUT PDN_DISCONNECT_TIMEOUT - MODIFICATION_REJECT - MODIFICATION_TIMEOUT - OVERWRITE - LOCALLY
Overwrite Mode
- NONE BEARER TYPE - DEFAULT_BEARER - DEDICATED_BEARER
© Copyright by Accuver Ltd.
Page 25
Samsung Common Basic Info
Parameter RAT
Description Radio Access Technology echno logy - GSM - GPRS - UMTS - EDGE - HSPA - LTE
Modem Status
Modem Status - INITIAL - ACQUISITION - IDLE - ACCESS - TRAFFIC - NO SERVICE
MIMO Type
MIMO Type - SISO - SIMO - MISO - MIMO
Rx Frequency
DL Frequency (MHz)
Tx Frequency
UL Frequency (MHz)
Common Data Info
Parameter
Description
DL Throughput
DL Throughput for GSM/GPRS/UMTS/EDGE/HSP GSM/GPRS/UMTS/EDGE/HSPA/ A/ LTE LTE
UL Throughput
UL Throughput for GSM/GPRS/UMTS/EDGE/HSP GSM/GPRS/UMTS/EDGE/HSPA/ A/ LTE LTE
DL BLER
DL Block Error Rate for GSM/GPRS/UMTS/EDGE/H GSM/GPRS/U MTS/EDGE/HSPA/ SPA/ LTE
DL BLER
DL Block Error Rate for GSM/GPRS/UMTS/EDGE/H GSM/GPRS/U MTS/EDGE/HSPA/ SPA/ LTE
DL FER
DL Frame Error Rate for GSM/GPRS/UMTS/EDGE/ GSM/GPRS/ UMTS/EDGE/HSPA/ HSPA/ LTE
UL FER
UL Frame Error Rate for GSM/GPRS/UMTS/EDGE/ GSM/GPRS/ UMTS/EDGE/HSPA/ HSPA/ LTE
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
LTE N Cell Information
Parameter EUTRAN>PLMN EUTRAN>Serving Cell Info> Cell ID EUTRAN>Serving Cell
Description PLMN Serving Cell ID(PCI 0 ~ 503) Serving Cell RSSI
Info>RSSI EUTRAN>Serving Cell
Serving Cell CINR
Info>CINR EUTRAN>Serving Cell
Serving Cell RSRP
Info>RSRP EUTRAN>Serving Cell
Serving Cell RSRQ
Info>RSRQ EUTRAN>Serving Cell
Serving Cell RSSI/CINR/RSRP/RSRQ per PCI
Info>All Cell Info EUTRAN>Neighbor Cell Info>NCell Num EUTRAN>Neighbor Cell Info>EARFCN EUTRAN>Neighbor Cell Info>RSSI EUTRAN>Neighbor Cell Info>RSRP EUTRAN>Neighbor Cell Info>RSRQ EUTRAN>Neighbor Cell Info>Top Set
Neighbor Cell number
Neighbor Cell EARFCN per Cell ID(PCI)
Neighbor Cell RSSI per Cell ID(PCI)
Neighbor Cell RSRP per Cell ID(PCI)
Neighbor Cell RSRQ per Cell ID(PCI) EARFCN
Top 1 to 20 EARFCN from Neighbor Cell
Cell ID
PCI with RSRP strength from top 1 to 20 from Neighbor Cell
RSSI
Top 1 to 20 RSSI from Neighbor Cell
RSRP
Top 1 to 20 RSRP from Neighbor Cell
RSRQ
Top 1 to 20 RSRQ from Neighbor Cell
EUTRAN>All Set
All(Serving/ All(Serving/Neighbo Neighbor) r) Cell Cell EARFCN/R EARFCN/RSSI/CI SSI/CINR/RS NR/RSRP/RS RP/RSRQ RQ per PCI
EUTRAN>Top Set
Cell ID
PCI with RSRP strength from top 1 to 20 from Neighbor Cell
EARFCN
Top 1 to 20 EARFCN from All(Serving/Neighbor) Cell
RSSI
Top 1 to 20 RSSI from All(Serving/Neighbor) Cell
RSRP
Top 1 to 20 RSRP from All(Serving/Neighbor) Cell
RSRQ
Top 1 to 20 RSRQ from All(Serving/Neighbor) Cell
Cell State UTRAN>UARFCN
© Copyright by Accuver Ltd.
Top 1 to 20 Cell State from All(Serving/Neighbor) Cell Serving, Neighbor
UARFCN per PSC
Page 27
UTRAN>RSSI
UTRAN RSSI per PSC
UTRAN>RSCP
UTRAN RSCP per PSC
UTRAN>Ec/Io
UTRAN Ec/Io per PSC
UTRAN>FDD/TDD
UTRAN FDD/TDD per PSC - FDD - TDD
UTRAN>Top Set
UARFCN
Top 1 to 20 UARFCN from UTRAN
PSC
PSC with Ec/Io strength from top 1 to 20 from UTRAN
RSSI
Top 1 to 20 RSSI from UTRAN
RSCP
Top 1 to 20 RSCP from UTRAN
Ec/Io
Top 1 to 20 Ec/Io from UTRAN
FDD/TDD
Top 1 to 20 FDD/TDD from UTRAN
GERAN>RSSI
GERAN RSSI per ARFCN
GERAN>BSIC
GERAN BSIC per ARFCN
GERAN>Top Set
CDMA2000>Frequency CDMA2000>Ec/Io CDMA2000>1xRTT/HR PD CDMA2000>PN Phase CDMA2000>Top Set
ARFCN ARFCN
ARFCN ARFCN with with RSSI RSSI strength strength from from top 1 to 20 from from GERAN GERAN
BSIC
Top 1 to 20 BSIC from GERAN
RSSI
Top 1 to 20 RSSI from GERAN
CDMA2000 Frequency per PN CDMA2000 Ec/Io per PN CDMA2000 1xRTT/HRPD per PN CDMA2000 PN Phase per PN Frequency
Top 1 to 20 Frequency from CDMA2000
PN
PN with Ec/Io strength from top 1 to 20 from CDMA2000
Ec/Io
Top 1 to 20 Ec/Io from CDMA2000
PN Phase
Top 1 to 20 PN Phase from CDMA2000
1xRTT/HRPD
Top 1 to 20 1xRTT/HRPD from CDMA2000
LPHY Cell Search Info
Parameter Cell ID CP type
Description Cell ID(PCI 0 ~ 503) Cyclic Prefix type - Normal - Extended
Antenna[x]>R Antenna[x]>RSRP SRP
Antenna[x] Antenna[x] RSRP RSRP (where, (where, x = 0 ~3)
Antenna[x]>R Antenna[x]>RSRQ SRQ
Antenna[x] Antenna[x] RSRQ RSRQ (where, (where, x = 0 ~3)
Antenna[x]>R Antenna[x]>RSSI SSI
Antenna[x] Antenna[x] RSSI RSSI (where, (where, x = 0 ~3)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
LPHY System Info
Parameter Transmission mode
Description Transmission mode - SISO - SIMO - 2TX SFBC - 4TX SFBC-FSTD - 2TX Open-loop SM-: 4TX Open-loop SM - 2TX Closed-loop SM, Rank=2 - 4TX Closed-loop SM, Rank=2 - 2TX Multi-user MIMO - 4TX Multi-user MIMO - 2TX Closed-loop SM, Rank=1 - 4TX Closed-loop SM, Rank=1 - port5 SISO - port5 SIMO
DL Pwr Control>Pa
Pa Index
Index
- [-6 dB] - [ -4.77 dB] - [-3 dB] - [-1.76 dB] - [0 dB] - [1 dB] - [2 dB] - [3 dB]
DL Pwr Control>Pb Index
Pb Index - 1 (One Antenna) - 4/5 (One Antenna) - 3/5 (One Antenna) - 2/5 (One Antenna) - 5/4 (Two or Four Antenna) - 1 (Two or Four Antenna) - 3/4 (Two or Four Antenna) - 1/2 (Two or Four Antenna)
DL Pwr Control>CQI
CQI feedback type(Aperiodic)
feedback
- Aperiodic Mode 1-2
type(Aperiodic)
- Aperiodic Mode 2-0 - Aperiodic Mode 2-2 - Aperiodic Mode 3-0 - Aperiodic Mode 3-1
© Copyright by Accuver Ltd.
Page 29
DL Pwr Control>CQI feedback type(Periodic)
CQI feedback type(Periodic) - Periodic Mode 1-0 - Periodic Mode 1-1 - Periodic Mode 2-0 - Periodic Mode 2-1
DL Pwr Control>Codebook
Codebook Subset Restriction
Subset Restriction
LPHY Channel Quality Info
Parameter
Description
CINR>CINR 0
CINR 0 for Ant 0
CINR>CINR 1
CINR 1 for Ant 1
CQI Metric>CQI Metric0
Channel Quality information Metric0
CQI Metric>CQI Metric1
Channel Quality information Metric1
CQI Metric>RI CQI Metric>PMI CQI Metric>Best PMI
Rank Indication Precoding Matrix Indicator Best Precoding Matrix Indicator
LPHY Parameter Info
Parameter DL System Info>DL BW
Description Downlink System Bandwidth - 1.4M - 3M - 5M - 10M - 15M - 20M
DL System Info>CP Type
DL System Cyclic Prefix type - Normal - Extended
DL System Info>eNB
-1
Ant Num Num
-2 -4
DL System Info>UE Ant
-1
Num
-2
DL System Info>Cell ID
Cell ID(PCI 0 ~ 503)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
UL System Info>UL BW
Uplink System Bandwidth - 1.4M - 3M - 5M - 10M - 15M - 20M
UL System Info>CP Type
UL System Cyclic Prefix type - Normal - Extended
LPHY PHICH Info
Parameter PHICH group number
Description Physical HARQ indicator channel group number (parameter to derive number of PHICH groups)
PHICH duration
Physical HARQ indicator channel duration - Short (Normal) - Extended
LL1 RF & Sync Info
Parameter
Description
RSSI Ant0
Received signal strength indication f or or Ant 0
RSSI Ant1
Received signal strength indication f or or Ant 1
TX Power
Transmitted Power
Sync Info>Cell ID
Sync Cell ID
Sync Info>SFN
Sync SFN
PBCH Info>Bandwidth
Bandwidth - 1.4M - 3M - 5M - 10M - 15M - 20M
PBCH Info>Phich Resource
PHICH Resource - 1/6 - 1/2 -1 -2
© Copyright by Accuver Ltd.
Page 31
PBCH Info>Phich
PHICH Duration
Duration
- Short (Normal) - Extended
PBCH Info>eNB Ant
eNB(LTE eNB(LTE Site) Antenna -1 -2
LL1 Downlink Info
Parameter PDSCH BLER RB Num
Description PDSCH Block Error Rate Resource Block Number for DL
MCS Level0
MCS Level0 for DL
MCS Level1
MCS Level1 for DL
Modulation0
Modulation0 (QPSK, 16QAM, 64QAM) for DL
Modulation1
Modulation1 (QPSK, 16QAM, 64QAM) for DL
LL1 Uplink Info
Parameter PUSCH BLER RB Num
Description PUSCH Block Error Rate Resource Block Number for UL
MCS Level
MCS Level for UL
Modulation
Modulation (QPSK, 16QAM, 64QAM) for UL (LTE UE CAPA 5 supports 64QAM.)
LL1 Measurement Config Info
Parameter
Description
S-measure
S-measure
Gap Pattern
Gap Pattern
Gap Start SFN Gap Start Subframe EUTRA quantity
Gap Start System Frame Number Gap Start Subframe EUTRA quantity
EUTRA FC RSRP
EUTRA Fc RSRP (where, Fc: Frequency of the carrier centre frequency)
EUTRA FC RSRQ
EUTRA Fc RSRQ (where, Fc: Frequency of the carrier centre frequency)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
LL2 SCH Configuration Info
Parameter DL SCH Config>Semi
Description Semi Persist Schedule Interval [Unit: sf]
Persist Sched Interval UL SCH Config>
Max HARQ-Tx [Unit: n]
MaxHARQ-Tx UL SCH Config>Semi
Semi Persist Schedule Interval [Unit: sf]
Persist Sched Interval UL SCH
Periodic Buffer Status Report timer [Unit: n]
Config>Periodic BSR timer
Timer & Preamble Info
Parameter Time Alignment Timer
Description Time Alignment Timer [Unit: sf]
Info>Time Alignment Timer PHR Configuration
Periodic PHR Timer [Unit: sf]
Info>Periodic PHR Timer PHR Configuration
PHR Prohibit Timer [Unit: sf]
Info>PHR Prohibit Timer PHR Configuration
DL Pathloss Change [Unit: dB]
Info>DL Pathloss Change Preamble Info>No. of
Number of RA-Preambles [Unit: n]
RA-Preambles Preamble Info>Size of
Size of RA-Preambles Group A [Unit: n]
RA-Preambles Group A
Power Ramping & RA Supervision S upervision Info
Parameter Power Ramping Param
Description Power Ramping Step[Unit: dB]
Info>Power Ramping Step
© Copyright by Accuver Ltd.
Page 33
Power Ramping Param
Preamble Initial Rx Target Target Power [Unit: [ Unit: dBm]
Info>Preamble Initial Rx Target Pwr RA Supervision
Preamble Trans Max [Unit: n]
Info>Preamble Trans Max RA Supervision Info>RA
RA Response Window Size [Unit: sf]
Response Window Size RA Supervision
MAC Contention Resolution Timer [Unit: sf]
Info>MAC Contention Resolution Timer
Max HARQ Msg3Tx & RACH Info
Parameter Max HARQ Msg3Tx
Description Max HARQ-Msg3Tx
Info>MaxHARQ-Msg3Tx RACH
Preamble ID
Info>PREAMBLE_ID RACH Info>Back Off
Back Off Timer Value [Unit: ms]
Timer Value RACH Info>Preamble
Preamble Counter
Counter
LL2 RNTI Info
Parameter
Description
SI-RNTI
SI-RNTI
P-RNTI
P-RNTI
Temp C-RNTI C-RNTI
Temporary empora ry C-RNTI C-RNTI
RA-RNTI
RA-RNTI
SPS-RNTI
SPS-RNTI
LL2 RLC Info
Parameter Uplink>RB ID [x]>UM SN length
Description UM SN length for Uplink (where, x = 0 ~ 31)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Uplink>RB ID [x]>Poll
Poll retransmit timer for Uplink (where, x = 0 ~ 31) [Unit: ms]
retransmit timer Uplink>RB ID [x]>Poll
Poll PDU for Uplink (where, x = 0 ~ 31)
PDU Uplink>RB ID [x]>Poll
Poll Byte for Uplink (where, x = 0 ~ 31) [Unit: kB]
Byte Uplink>RB ID [x]>Max
Max Retransmit threshold for Uplink (where, x = 0 ~ 31) [Unit: n]
Retransmit threshold Uplink>RB ID [x]>Active
Active Active Info for for Uplink Uplink (where, (where, x = 0 ~ 31) 31)
Info Downlink>RB ID [x]>UM
UM SN length for Downlink (where, x = 0 ~ 31)
SN length Downlink>RB ID [x]>T1
T1 time value for Downlink (where, x = 0 ~ 31) [Unit: ms]
time value Downlink>RB ID
Status Prohibit timer value for Downlink (where, x = 0 ~ 31) [Unit: ms]
[x]>Status [x]>Status Prohibit timer value Downlink>RB ID [x]>Active Info
Active Active Info for for Downlink Downlink (where, (where, x = 0 ~ 31) - Deactive - Active
LL2 PDCP Info
Parameter
Description
Uplink>PDCP Info Num
Uplink PDCP PDCP Info Number (where, x = 0 ~ 31)
Uplink>RB ID
Connection Info for Uplink (where, x = 0 ~ 31)
[x]>Connection Info
- invalid - valid
Uplink>RB ID [x]>Integrity Protection Flag
Integrity Protection Flag for Uplink (where, x = 0 ~ 31) - Null - Snow3G - AES
Uplink>RB ID [x]>Ciphering Flag
Ciphering Flag for Uplink (where, x = 0 ~ 31) - Null - Snow3G - AES
Uplink>RB ID [x]>SN Window Size
SN Window Size for Uplink (where, x = 0 ~ 31) - SRBs - DRBs on RLC UM - DRBs on RLC UM or AM
© Copyright by Accuver Ltd.
Page 35
Uplink>RB ID [x]>SDU Discard Timer
SDU Discard Timer for Uplink (where, x = 0 ~ 31) - Discard timer disable - Discard timer time (0x01 ~ 0xFE) [Unit: ms] - Infinity
Downlink>PDCP Info
Downlink PDCP Info Number (where, x = 0 ~ 31)
Num Downlink>RB ID [x]>Connection Info
Connection Info for Downlink (where, x = 0 ~ 31) - invalid - valid
Downlink>RB ID [x]>Integrity Protection Flag
Downlink>RB ID [x]>Integrity Protection Flag for Downlink (where, x = 0 ~ 31) - Null - Snow3G - AES
Downlink>RB ID [x]>Ciphering Flag
Downlink>RB ID [x]>Ciphering Flag for Downlink (where, x = 0 ~ 31) - Null - Snow3G - AES
Downlink>RB ID [x]>SN Window Size
Downlink>RB ID [x]>SN Window Size for Downlink (where, x = 0 ~ 31) - SRBs - DRBs on RLC UM - DRBs on RLC UM or AM
LRRC Serving Cell Info
Parameter Global Cell ID Band
Description Global Cell ID Band (Band 1 ~ 14, 17, 33 ~ 40)
PLMN ID
PLMN ID
TAC List
TAC List (TAC[0] & TAC[1])
LRRC State Variables Info
Parameter RRC State
Description RRC State - NULL - IDLE - CONNECTED - DISCONNECTING
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
LRRC Timer info
Parameter T300
Description Timer 300 (Start) Transmission of RRCConnectionRequest (Stop) Reception of RRCConnectionSetup or RRCConnectionReject message, cell reselection and upon abortion of connection establishment by upper layers (At expiry) Perform the actions as specified in 3GPP 36.331 5.3.3.6
T301
Timer 301 (Start) Transmission of RRCConnectionReestabilshmentRequest (Stop) Reception of RRCConnectionReestablishment or RRCConnectionReestablishmentReject message as well as when the selected cell becomes unsuitable (At expiry) Go to RRC_IDLE
T310
Timer 310 (Start) Upon detecting physical layer problems i.e. upon receiving N310 consecutive out-ofsync indications from lower layers (Stop) Upon receiving N311 consecutive in-sync indications from lower layers, upon triggering the handover procedure and upon initiating the connection reestablishment procedure (At expiry) If security is not activated: go to RRC_IDLE else: initiate the connection reestablishment procedure
T311
Timer 311 (Start) Upon initiating the RRC connection re-establishment procedure (Stop) Selection of a suitable E-UTRA cell or a cell using another RAT (At expiry) Enter RRC_IDLE
LNAS State Variables Info
© Copyright by Accuver Ltd.
Page 37
Parameter EMM Functional State
Description EMM Functional State - DETACHED - IDLE - CONNECTED
EMM State
EMM State - NULL - DEREGISTERED - REGISTERED_INITIA REGISTERED_INITIATED TED - REGISTERED - TAU_INITIATED - SERVICE_REQUEST_INITIAT SERVICE_REQUEST_INITIATED ED - DEREGISTERED_INITIA DEREGISTERED_INITIATED TED
LNAS MM(SIM/PLMN/Security) Info
Parameter SIM Data Info>TAI Info >TAI SIM Data Info>S-TMSI SIM Data Info>SIM
Description TAI S-TMSI SIM Update status
Update status SIM Data Info>IMSI
IMSI
SIM Data Info>GUTI
GUTI
SIM Data Info>HPLMN
HPLMN search period
search period PLMN Selection
Registered PLMN
Info>Registered PLMN Security Info>Status
Security Status 0: Enable 1: Disable
Security Info>NAS KSI
NAS KSI
Security Info>CK
CK
Security Info>IK
IK
Security Info>Security algo integrity
Security algorithm integrity - INTEG_NULL_ALGO - INTEG_SNOW3G_ALGO - INTEG_AES_ALGO
Security Info>Security algo ciphering
Security algorithm ciphering - INTEG_NULL_ALGO - INTEG_SNOW3G_ALGO - INTEG_AES_ALGO
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
LNAS PDP/IP Info
Parameter PDP Info IP Info>IPv4 Address IP Info>IP Mode
Description EPS Bearer Id, Bearer Type and SM Cause IP v4 Address IP Mode - IPv4 - IPv6 - IPv4_IPv6
LDATA Throughput Info
Parameter Physical Layer>UL Throughput Physical Layer>DL Throughput
Description LTE LTE PUSCH Throughput [Unit: [Unit : Mbps]
LTE LTE PDSCH Throughput [Unit: [Unit : Mbps]
LDATA Timing Info
Parameter Connection time
© Copyright by Accuver Ltd.
Description Connection time by Samsung LTE LTE chipset chipset [Unit: ms]
Page 39
Qualcomm Configuration Info
Parameter
Description
DL Common> TDD
0 – SUBFRAME_ASSIGN_0
Common Config
1 – SUBFRAME_ASSIGN_1 2 – SUBFRAME_ASSIGN_2 Subframe Assignment
3 – SUBFRAME_ASSIGN_3 4 – SUBFRAME_ASSIGN_4 5 – SUBFRAME_ASSIGN_5 6 – SUBFRAME_ASSIGN_6 0 – SPECIAL_SUBFRAME_PATTERN_0 1 – SPECIAL_SUBFRAME_PATTERN _1 2 – SPECIAL_SUBFRAME_PATTERN _2
Special Subframe Patterns
3 – SPECIAL_SUBFRAME_PATTERN _3 4 – SPECIAL_SUBFRAME_PATTERN _4 5 – SPECIAL_SUBFRAME_PATTERN _5 6 – SPECIAL_SUBFRAME_PATTERN _6 7 – SPECIAL_SUBFRAME_PATTERN_7 8 – SPECIAL_SUBFRAME_PATTERN_8
DL Common> UL CP Config DL Common> UL Config
UL CP UL EARFCN
0 – NORMAL_CP 1 – EXTENDED_CP UL Cell earfcn (18000 <= Range <= 39649) Uplink bandwidth 6 (RBs) – 1.4 MHz 15 (RBs) – 3 MHz
UL Bandwidth
25 (RBs) – 5 MHz 50 (RBs) – 10 MHz 75 (RBs) – 15 MHz 100 (RBs) – 20 MHz
Additional Additional Spectru Spectrum m Emission DL Common> MIB info
Num ENB Ant Ports
Additional Additional Spectru Spectrum m Emissio Emission n (Range (Range is 1 to 32) Valid values – 1, 2, 4 PHICH-Duration
PHICH Duration
0 – PHICH_NORMAL 1 – PHICH_EXTENDED
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Ng (HICH group multiplier) 0 – 1/6 PHICH Resource
1 – 1/2 2 – 1 3 – 2
DL Common> PDSCH Config
Reference Signal Power
Downlink Reference-signal transmit power (Range is -60 to 50 dBm) P_B indicates the ratio of PDSCH-to-RS EPRE in symbols with and without reference symbols for 1, 2 or 4 cell specific antenna ports
P-b
0 – PB0 = (1, 1), (2, 5/4), (4, 5/4) 1 – PB1 = (1, 4/5), (2, 1), (4, 1) 2 – PB2 = (1, 3/5), (2, 3/4), (4, 3/4) 3 – PB3 = (1, 2/5), (2, 1/2), (4, 1/2) 4 – PB_FW_HYPOTHESIS
DL Common> MBSFN
Allocation Allocation Offset Offset
Config> Config[x]
allocation allocation offset offset (Range (Range is 0 to 7) 7) allocation period 0 – 1 radio frame 1 – 2 radio frames
Allocation Allocation Period Period
2 – 4 radio frames 3 – 8 radio frames 4 – 16 radio frames 5 – 32 radio frames subfn allocation type
Sub-Fn Allocation Type Type
Type 0 – MBSFN allocation one frame Type 1 – MBSFN allocation four frames subfn allocation mask based on subfn allocation type
Sub-Fn Allocation Mask
- First 6 bits (least significant bits) for Type 0 - All 24 bits for Type 1 - Total 24 bits mask
DL Dedicated> PDCCH TPC Config for PUCCH
TPC-RNTI
RNTI for PUCCH power control using DCI format 3/3A (Range is 0001-003C, 003D-FFF3) DCI format 3 or 3A used for TPC Index
DCI Format
0 – DCI Format3 1 – DCI Format3A Index of N or M
TPC Index
(Range is [1-15] for DCI format 3 and [1-31] for format 3A)
DL Dedicated> PDCCH TPC Config for PUSCH
TPC-RNTI
RNTI for PUSCH power control using DCI format 3/3A (Range is 0001-003C, 003D-FFF3) DCI format 3 or 3A used for TPC Index
DCI Format
0 – DCI Format3 1 – DCI Format3A
© Copyright by Accuver Ltd.
Page 41
Index of N or M TPC Index
(Range is [1-15] for DCI format 3 and [1-31] for format 3A)
Antenna Antenna Config Config
A bitmask bitmask of the the codebook codebook restric restriction. tion. The The number number of bits bits used in the restriction varies with the transmission mode n2TxAntenna-tm3 : 2 n4TxAntenna-tm3 : 4 Codebook Subset
n2TxAntenna-tm4 : 6
Restriction
n4TxAntenna-tm4 : 64 n2TxAntenna-tm5 : 4 n4TxAntenna-tm5 : 16 n2TxAntenna-tm6 : 4 n4TxAntenna-tm6 : 16 Transmission mode 1 – Tx mode 1 2 – Tx mode 2
Transmission Mode
3 – Tx mode 3 4 – Tx mode 4 5 – Tx mode 5 6 – Tx mode 6 7 – Tx mode 7
Tx Ant Selection Control DL Dedicated> PDSCH
0 – Closed loop 1 – Open loop P-a
Config
0 – - 6 dB 1 – - 4.77 dB 2 – - 3 dB P-a
3 – - 1.77 dB 4 – 0 dB 5 – 1 dB 6 – 2 dB 7 – 3 dB 8 – PA_FW_HYPOTHESIS
DL Dedicated> UErelated Config UL Common> PUSCH Config
C-RNTI
n_sb
C- RNTI value (Range is 0001-003C, 003D-FFF3) n_sb 0x0 - 1 to 0x3 – 4 Hopping-mode
Hopping Mode
0x0 - Inter subframe 0x1 - Intra and inter subframe
Hopping Offset
Hopping offset (Range is 0 to 98)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Enable 64 QAM
1 indicates that 64 QAM is enabled while 0 indicates that no 64 QAM is allowed Group-hopping-enabled
Group Hopping Enabled
1 indicates that Group Hopping is enabled while 0 Indicates that Group Hopping is disabled
Group Assignment PUSCH Sequence Hopping Enabled
UL Common> PUCCH Config
UL Common> SRS Config
Group Assignment PUSCH (Range is 0 to 29) Sequence-hopping-enabled 1 indicates that Sequence Hopping is enabled while 0 Indicates that Sequence Hopping is disabled
Cyclic Shift
Cyclic Shift (Range is 0 to 7)
Delta Shift
Delta Shift (Range is 1 to 3)
n_rb_cqi
n_rb_cqi (Range is 0 to 98)
n_cs_an
n_cs_an (Range is 0 to 7)
n1_pucch_an
n1_pucch_an (Range is 0 to 2047)
SRS Enabled
0x0 – Disable 0x1 – Enable
SRS Bandwidth Config
SRS Bandwidth Configuration (Range is 0 to 7)
SRS Subframe Config
SRS subframe Configuration (Range is 0 to 15)
Simultaneous ACK/NAK SRS
Simultaneous-AN-and-SRS 1 indicates that Simultaneous transmission of ACK/NAK and SRS is enabled while 0 Indicates that it is disabled SRS Max Uplink Pilot Time Slot
SRS Max UpPts
1 indicates reconfiguration is enabled for UpPts while 0 indicates that reconfiguration is disabled.
UL Dedicated> SRS Config
SRS Enabled SRS Bandwidth SRS Hopping Bandwidth Freq Domain Position Duration
UL Dedicated> CQI Config
© Copyright by Accuver Ltd.
0x0 – Disable 0x1 – Enable SRS Bandwidth (Range is 0 to 3) SRS hopping bandwidth (Range is 0 to 3) Frequency Domain Position (Range is 0 to 23) 0 corresponds to single and value 1 to indefinite (Range is 0 to 1)
SRS Config Index
SRS Config Index (Range is 0 to 1023)
Tx Combination
Tx Combination (Range is 0 to 1)
Cyclic Shift
Cyclic Shift (Range is 0 to 7)
CQI Enabled
0x0 – Disable 0x1 – Enable
Page 43
CQI Reporting Mode Aperiodic 0x0 – Mode12 CQI Reporting Mode
0x1 – Mode20
Aperiodic Aperiodic
0x2 – Mode22 0x3 – Mode30 0x4 – Mode31
CQI Reporting Periodic
0x0 – Not Present
Present
0x1 - Present PUCCH CQI Feedback Type
CQI Format Indicator
0x0 – Wideband CQI 0x1 – Subband CQI
Nominal PDSCH RS
Nominal PDSCH RS EPRE Offset
EPRE Offset
(Range is -1 to 6)
CQI PUCCH Resource
CQI PUCCH Resource Index
Index
(Range is 0 to 1185)
RI Config Index K Simultaneous AckNack and CQI
CQI-PMI Config Index UL Dedicated> Antenna Dedicated> Antenna
RI Config Index (Range is 1 to 1023) K (Range is 1 to 4) Simultaneous-AN-and-CQI 1 indicates that simultaneous transmission of ACK/NACK and CQI is allowed and 0 indicates that it is not CQI/PMI Periodicity and offset Configuration Index (Range is 0 to 1023) Transmission mode
Config
1 – Tx mode 1 2 – Tx mode 2 Transmission Mode
3 – Tx mode 3 4 – Tx mode 4 5 – Tx mode 5 6 – Tx mode 6 7 – Tx mode 7
Tx Ant Selection Enabled Tx Ant Selection Control Codebook Subset Restriction
0 indicates that UE transmit antenna selection is disabled. If 1, then the field indicates whether UE transmit antenna selection control is closed-loop or open-loop 0 indicates closed closed loop and 1 indicates open loop Codebook Subset Restriction
GM Common> UL
ul-EARFCN
Frequency Config
For FDD – Default value determined from default Cell Frequency
Tx-RX frequency separation defined in [36.101] Range is For TDD – This parameter is absent and it is equal to the downlink frequency.
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Bandwidth Additional Additional Spectru Spectrum m Emission GM Common> PUCCH Config
GM Common> UL
Uplink bandwidth Additional Additional Spectru Spectrum m Emissio Emission n (Range (Range is 0 to 31)
PUCCH Delta Shift
PUCCH Delta Shift (Range is 1 to 3)
n_rb_cqi
n_rb_cqi (Range is 0 to 98)
n_cs_an
n_cs_an (Range is 0 to 7)
n1_pucch_an
n1_pucch_an (Range is 0 to 2047)
P0 Nominal PUSCH
P0 Nominal PUSCH (Range is -126 to 24)
Power Control Config
Alpha 0x0 – 0 0x1 – 0.4 0x2 – 0.5 Alpha
0x3 – 0.6 0x4 – 0.7 0x5 – 0.8 0x6 – 0.9 0x7 – 1.0
P0 Nominal PUCCH Delta Preamble MSG3 Delta TF List PUCCH Format 1 Delta TF List PUCCH Format 1b Delta TF List PUCCH Format 2 Delta TF List PUCCH Format 2a Delta TF List PUCCH Format 2b GM Common> SRS Config
SRS Enabled
P0 Nominal PUCCH (Range is -127 to -96) actual value = IE value * 2 [dB] Delta Preamble MSG3 Delta TF List PUCCH Format 1
Delta TF List PUCCH Format 1b
Delta TF List PUCCH Format 2
Delta TF List PUCCH Format 2a
Delta TF List PUCCH Format 2b 0x0 – Disable 0x1 – Enable
SRS Bandwidth Config
SRS bandwidth configuration (Range is 0 to 7)
SRS Subframe Config
SRS subframe configuration (Range is 0 to 15)
Simultaneous ACK/NAK SRS
Simultaneous-AN-and-SRS 1 indicates that Simultaneous transmission of ACK/NAK and SRS is enabled while 0 Indicates that it is disabled SRS Max Uplink Pilot Time Slot
SRS Max UpPts
1 indicates reconfiguration is enabled for UpPts while 0 indicates that reconfiguration is disabled
© Copyright by Accuver Ltd.
Page 45
GM Common> UL Cyclic Prefix Config
Uplink cyclic prefix length UL Cyclic Prefix Length
0 corresponds to normal cyclic prefix and 1 corresponds to extended cyclic prefix
GM Common> PUSCH Config GM Dedicated> SR Config
Enable 64 QAM
SR Enabled SR PUCCH Resource Index SR Config Index SR Max Transmissions
GM Dedicated> CQI Config
CQI Enabled
0x0 – Disable 0x1 – Enable 0x0 – Disable 0x1 – Enable SR PUCCH Resource Index (Range is 0 to 2047) SR Config Index (Range is 0 to 155) SR Max Transmissions(DSR_TRANS_MAX) Transmissions(DSR_TRANS_MAX) (Range is 4 to 64) 0x0 – Disable 0x1 – Enable CQI Reporting Mode Aperiodic 0x0 – Mode12
CQI Reporting Mode
0x1 – Mode20
Aperiodic Aperiodic
0x2 – Mode22 0x3 – Mode30 0x4 – Mode31
Nominal PDSCH RS
Nominal PDSCH RS EPRE Offset
EPRE Offset
(Range is -1 to 6)
CQI Reporting Periodic
0x0 – Not Present
Present
0x1 - Present
CQI Reporting Periodic
0x0 – Disable
Enabled
0x1 – Enable PUCCH CQI Feedback Type
CQI Format Indicator
0x0 – Wideband CQI 0x1 – Subband CQI
Simultaneous AckNack and CQI
and CQI is allowed and 0 indicates that it is not CQI PUCCH Resource Index
Index
(Range is 0 to 1185)
K CQI-PMI Config Index
Config
1 indicates that simultaneous transmission of ACK/NACK
CQI PUCCH Resource
RI Config Index
GM Dedicated> SRS
Simultaneous-AN-and-CQI
SRS Enabled SRS Bandwidth
RI Config Index (Range is 1 to 1023) K (Range is 1 to 4) CQI/PMI Periodicity and offset Configuration Index (Range is 0 to 1023) 0x0 – Disable 0x1 – Enable SRS Bandwidth (Range is 0 to 3)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
SRS Hopping Bandwidth Freq Domain Position Duration
GM Dedicated> PHR Config
0 corresponds to single and value 1 to indefinite (Range is 0 to 1) Tx Combination (Range is 0 to 1)
Cyclic Shift
Cyclic Shift (Range is 0 to 7)
SRS Config Index
SRS Config Index (Range is 0 to 1023)
PHR Enabled
Prohibit PHR Timer
TPC Config
Frequency Domain Position (Range is 0 to 23)
Tx Combination
Periodic PHR Timer
GM Dedicated> PUSCH
SRS hopping bandwidth (Range is 0 to 3)
0x0 – Disable 0x1 – Enable PERIODIC_PHR_TIMER Value Value in number of subframes (Range is 0 to 1000). PROHIBIT PHR TIMER Value Value in number of subframes (Range is 0 to 1000).
DL Pathloss Change
DL Pathloss Change Value in dB
Threshold
(Range is 0 to 6)
PUSCH TPC Enabled
0x0 – Disable 0x1 – Enable
PUSCH TPC DCI
0x0 - Format 3
Format
0x1 – Format 3a Index of N or M
PUSCH TPC Index
N or M is dependent on the used DCI format (Range is 1 to 31)
PUSCH TPC-RNTI GM Dedicated> PUCCH TPC Config
PUCCH TPC Enabled
RNTI for PUSCH power control using DCI format 3/3A 0x0 – Disable 0x1 – Enable
PUCCH TPC DCI
0x0 - Format 3
Format
0x1 – Format 3a Index of N or M
PUCCH TPC Index
N or M is dependent on the used DCI format (Range is 1 to 31)
PUCCH TPC-RNTI GM Dedicated> UL SCH Config
MAX HARQ Transmissions TTI Bundling Enabled
GM Dedicated> UL Power Control Config
RNTI for PUCCH power control using DCI format 3/3A max-HARQ-Tx (Range is 1 to 28) Configures TTI bundling on and OFF; can be configured for FDD and for TDD only for configurations 0, 1 and 6 Accumulation Accumulation-enabled enabled
Accumulation Enabled
1 corresponds to enabled, whereas 0 corresponds to disabled
P0 UE PUSCH
© Copyright by Accuver Ltd.
P0 UE PUSCH (Range is -8 to 7)
Page 47
P0 UE PUCCH
P0 UE PUCCH (Range is -8 to 7) Delta MCS Enabled
Delta MCS Enabled
0 corresponds to value 0 corresponding to state disabled; 1 corresponds to value 1.25 corresponding to enabled P_SRS Offset
P_SRS Offset
For Ks=1.25, the actual parameter value is pSRS-offset value – 3. For Ks=0, the actual parameter value is -10.5 + 1.5*pSRS-offset value.
GM Dedicated> PUSCH
Delta Offset ACK Index
Delta Offset ACK Index (Range is 0 to 15)
Config
Delta Offset CQI Index
Delta Offset CQI Index (Range is 0 to 15)
Delta Offset Index
Delta Offset Index (Range is 0 to 15)
GM Dedicated> PUCCH Config
PUCCH Cfg Enabled
0x0 – Disable 0x1 – Enable ACK/NAK ACK/NAK Feedback Feedback Mode Parameter indicates one of the two TDD ACK/NACK
ACK/NAK ACK/NAK Feedback Feedback Mode
feedback modes used 0 corresponds to use of ACK/NACK bundling, whereas 1 corresponds to ACK/NACK multiplexing The same value applies to both ACK/NACK feedback modes on PUCCH as well as on PUSCH
ACK/NAK ACK/NAK Repetitio Repetition n Factor
n1_PUCCH_ANRep
ACK/NAK ACK/NAK Repetitio Repetition n Factor Factor Parameter indicates whether ACK/NACK repetition is enable or disabled (Range is 2 to 6) PUCCH Resource for ACK/NAK Repetition (Range is 0 to 2047)
GM Dedicated>
Transmission mode
Antenna Antenna Config Config
1 – Tx mode 1 2 – Tx mode 2 Transmission Mode
3 – Tx mode 3 4 – Tx mode 4 5 – Tx mode 5 6 – Tx mode 6 7 – Tx mode 7
Tx Ant Selection Enabled Tx Ant Selection Control Codebook Subset Restriction GM Dedicated> CDRX Config
CDRX Enable
0 indicates that UE transmit antenna selection is disabled. If 1, then the field indicates whether UE transmit antenna selection control is closed-loop or open-loop 0 indicates closed closed loop and 1 indicates open loop Codebook Subset Restriction 0x0 – Disable 0x1 – Enable
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
On Duration Timer
Inactivity Timer
DL DRX Retx Timer
Long Cycle Len
Cycle Start Offset
On Duration Timer pdcch subframes (Maximum value 200) Inactivity Timer pdcch subframes (Maximum value 2560) DL DRX Retx Timer pdcch subframes (Maximum value 33) Long Cycle Len pdcch subframes (Maximum value 2560) Cycle Start Offset pdcch subframes (Maximum value 2559)
Short DRX Cycle
0x0 – Disable
Enable
0x1 – Enable
Short DRX Cycle Len
Short DRX Timer PRACH
Short DRX Cycle Len pdcch subframes (Maximum value 640) Short DRX Timer pdcch subframes (Maximum value 16) Logical Root ZadOFF-Chu Sequence number for various
Logical Root Seq Index
preamble formats Range is 0 to 837 for Preamble Format 0-3 Range is 0 to 137 for Preamble Format 4
RA Preamble Timing
High Speed Flag PRACH Frequency Offset
Random Access Preamble timing for a range of Preamble Formats (Range is 0 to 15) Controls grouping of preamble sequences in two sets, to differentiate a high speed UE from normal Frequency Resource offset (Range is 0 to 104)
Max Transmissions
Maximum number of HARQ re-transmissions from UE for
MSG3
RACH message3 (Range is 1 to 8) Cyclic Shifts for various Preamble Formats
Cyclic Shift Zone Length
Range is 0 to15 for Preamble Formats 0-3 Range is 0 to 6 for Pramble Format 4
RA Response Window
Window size for reception of RACH message2
Size
(Range is 2 to 10)
TDD
0 – SUBFRAME_ASSIGN_0 1 – SUBFRAME_ASSIGN_1 2 – SUBFRAME_ASSIGN_2 Subframe Assignment
3 – SUBFRAME_ASSIGN_3 4 – SUBFRAME_ASSIGN_4 5 – SUBFRAME_ASSIGN_5 6 – SUBFRAME_ASSIGN_6
© Copyright by Accuver Ltd.
Page 49
0 – SPECIAL_SUBFRAME_PATTERN_0 1 – SPECIAL_SUBFRAME_PATTERN _1 2 – SPECIAL_SUBFRAME_PATTERN _2 Special Subframe Patterns
3 – SPECIAL_SUBFRAME_PATTERN _3 4 – SPECIAL_SUBFRAME_PATTERN _4 5 – SPECIAL_SUBFRAME_PATTERN _5 6 – SPECIAL_SUBFRAME_PATTERN _6 7 – SPECIAL_SUBFRAME_PATTERN_7 8 – SPECIAL_SUBFRAME_PATTERN_8
Power Info
Parameter RSSI(In-band)
RSSI(Total Band)
RSSI(Broadband)
Tx Power
Description Ant0
RSSI(In-band) RSSI(In-band) for Ant0 (Range: (Range: -120 dBm dBm to -10 -10 dBm) dBm)
Ant1
RSSI(In-band) RSSI(In-band) for Ant1 (Range: (Range: -120 dBm dBm to -10 -10 dBm) dBm)
Comb
[RSSI(In-band)>Ant0 + RSSI(In-band)>Ant1]/2
Ant0
RSSI(T RSSI(Total Band) Band) for Ant0 (Range: (Range: -120 dBm dBm to -10 -10 dBm) dBm)
Ant1
RSSI(T RSSI(Total Band) Band) for Ant1 (Range: (Range: -120 dBm dBm to -10 -10 dBm) dBm)
Comb
[RSSI(Total [RSSI(Total Band)>Ant0 + RSSI(Total RSSI(Total Band)>Ant1]/2
Ant0
RSSI(Broadba RSSI(Broadband) nd) for Ant0 (Range: (Range: -120 -120 dBm to -10 dBm)
Ant1
RSSI(Broadba RSSI(Broadband) nd) for Ant1 (Range: (Range: -120 -120 dBm to -10 dBm)
Comb
[RSSI(Broadband)>Ant0 + RSSI(Broadband)>Ant1]/2
PUSCH
PUSCH Tx Power (Range: -112 -112 dBm to 23 dBm)
PUCCH
PUCCH Tx Power (Range: -112 dBm to 23 dBm)
PRACH
PRACH Tx Power (Range: -112 -112 dBm to 23 dBm)
SRS
SRS Tx Power (Range: -112 dBm to 23 dBm)
AGC
AGC Tx Power Power (Range: (Range: -70 dBm to 32.3 dBm)
Cell Search
Parameter PSS> Dominant PSS Peak Value PSS> Dominant PSS Peak Position PSS> Dominant PSS Indices SSS> Dominant PCI
Description Dominant PSS Peak value 10log10(x/128) in units of dB Sample position with 5 ms resolution (Range is 0 to (9600-1))
PSS Index (Range is 0 to 2) Dominant Cell ID(PCI)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
SSS> Dominant SSS Peak Value SSS> Dominant SSS Position SSS> Detected Cell Info> PCI#
Dominant SSS Peak Value 10log10(x/256) in units of dB Start of SSS sequence in search sample server. Range is 0 to (search sample server length -1) SSS Peak Value SSS Position
SSS Peak value per PCI SSS Position per PCI Cyclic prefix used per PCI
CP
0 – normal CP 1 – extended CP
Half Frame Hypothesis
Half Frame Hypothesis per PCI 0 – Preamble 1 – MIDamble
Ant Correlation Result
Parameter Serving PCI
Description Serving Cell PCI
RSSI Ant0
RSSI per Rx antenna0
RSSI Ant1
RSSI per Rx antenna1
RSSI Comb Antenna Correlation> Correlation> Correlation Real> Tx Ant[x] Ant[x] Antenna Correlation> Correlation> Correlation Imaginary> Tx Ant[x]
Combined RSSI Real part of Rx0 and Rx1 correlation Where, x is Tx Antenna (Range: 0 ~ 3).
Imaginary part of Rx0 and Rx1 correlation Where, x is Tx Antenna (Range: 0 ~ 3).
Intrafreq Measurement Info
Parameter EARFCN Frequency Serving Cell> Serving PCI
Description Downlink frequency as E-ARFCN Downlink frequency of the serving cell (Unit: MHz) Serving Cell PCI (Range: 0 ~ 503)
Serving Cell> Serving
RSRP
Serving Cell RSRP (Range: -140dBm to -44dBm)
RSRP
RSRP0
Serving Cell RSRP0 (Range: -140dBm to -44dBm)
RSRP1
Serving Cell RSRP1 (Range: -140dBm to -44dBm)
RSRQ
Serving Cell RSRQ (Range: -30dB to 0 dB)
Serving Cell> Serving
© Copyright by Accuver Ltd.
Page 51
RSRQ
RSRQ0
Serving Cell RSRQ0 (Range: -30dB to 0 dB)
RSRQ1
Serving Cell RSRQ1 (Range: -30dB to 0 dB)
Serving Cell> Serving
RSSI
Serving Cell RSSI (Range: -140dBm to -44dBm)
RSSI
RSSI0
Serving Cell RSSI0 (Range: -140dBm to -44dBm)
RSSI1
Serving Cell RSSI1 (Range: -140dBm to -44dBm)
Serving Cell> Serving
SINR0
Serving Cell SINR0 (Range: -20dB to +30dB)
SINR
SINR1
Serving Cell SINR1 (Range: -20dB to +30dB)
Serving Cell> All Cell
RSRP>PCI#
Serving Cell RSRP per PCI (Range: -140dBm to -44dBm)
Info> Serving RSRP
RSRP0>PCI#
Serving Cell RSRP0 per PCI (Range: -140dBm to -44dBm)
RSRP1>PCI#
Serving Cell RSRP1 per PCI (Range: -140dBm to -44dBm)
Serving Cell> All Cell
RSRQ>PCI#
Serving Cell RSRQ per PCI (Range: -30dB to 0 dB)
Info> Serving RSRQ
RSRQ0>PCI#
Serving Cell RSRQ0 per PCI (Range: -30dB to 0 dB)
RSRQ1>PCI#
Serving Cell RSRQ1 per PCI (Range: -30dB to 0 dB)
Serving Cell> All Cell
RSSI>PCI#
Serving Cell RSSI per PCI (Range: -140dBm to -44dBm)
Info> Serving RSSI
RSSI0>PCI#
Serving Cell RSSI0 per PCI (Range: -140dBm to -44dBm)
RSSI1>PCI#
Serving Cell RSSI1 per PCI (Range: -140dBm to -44dBm)
Serving Cell> All Cell
SINR0>PCI#
Serving Cell SINR0 per PCI (Range: -20dB to +30dB)
Info> Serving SINR
SINR1>PCI#
Serving Cell SINR1 per PCI (Range: -20dB to +30dB)
Neighbor Cell> Neighbor Neighbor Cell> Cell
Number of Neighbor PCI
Count Neighbor Cell> Neighbor Cell List
Neighbor PCI List
Neighbor Cell> Summary Neighbor Cell
Neighbor PCI List with (RSRP,RSRQ) (RSRP,RSRQ)
List Neighbor Cell> Neighbor RSRP>PCI# RSRP
RSRP0>PCI#
Neighbor Cell RSRP0 per PCI (Range: -140dBm to -44dBm)
RSRP1>PCI#
Neighbor Cell RSRP1 per PCI (Range: -140dBm to -44dBm)
Neighbor Cell> Neighbor RSRQ>PCI# RSRQ
Neighbor Cell> Top Set> Top#
Neighbor Cell RSRQ per PCI (Range: -30dB to 0 dB)
RSRQ0>PCI#
Neighbor Cell RSRQ0 per PCI (Range: -30dB to 0 dB)
RSRQ1>PCI#
Neighbor Cell RSRQ1 per PCI (Range: -30dB to 0 dB)
Neighbor Cell> Neighbor RSSI>PCI# RSSI
Neighbor Cell RSRP per PCI (Range: -140dBm to -44dBm)
Neighbor Cell RSSI per PCI (Range: -140dBm to -44dBm)
RSSI0>PCI#
Neighbor Cell RSSI0 per PCI (Range: -140dBm to -44dBm)
RSSI1>PCI#
Neighbor Cell RSSI1 per PCI (Range: -140dBm to -44dBm)
PCI
PCI with RSRP strength from top 1 to 20 from Neighbor Cell
RSRP
Top 1 to 20 RSRP from Neighbor Cell
RSRP0
Top 1 to 20 RSRP0 from Neighbor Cell
RSRP1
Top 1 to 20 RSRP1 from Neighbor Cell
RSRQ
Top 1 to 20 RSRQ from Neighbor Cell
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
All Set> Set> All RSRP RSRP
All Set> Set> All All RSRQ RSRQ
All Set> Set> All All RSSI RSSI
All Set> Set> Cell State State
RSRQ0
Top 1 to 20 RSRQ0 from Neighbor Cell
RSRQ1
Top 1 to 20 RSRQ1 from Neighbor Cell
RSSI
Top 1 to 20 RSSI from Neighbor Cell
RSSI0
Top 1 to 20 RSSI0 from Neighbor Cell
RSSI1
Top 1 to 20 RSSI1 from Neighbor Cell
RSRP>PCI#
RSRP per PCI
RSRP0>PCI#
RSRP0 per PCI
RSRP1>PCI#
RSRP1 per PCI
RSRQ>PCI#
RSRQ per PCI
RSRQ0>PCI#
RSRQ0 per PCI
RSRQ1>PCI#
RSRQ1 per PCI
RSSI>PCI#
RSSI per PCI
RSSI0>PCI#
RSSI0 per PCI
RSSI1>PCI#
RSSI1 per PCI
Cell State State per per PCI - Serving - Neighbor
Top Set> Top#
PCI
PCI with RSRP strength from top 1 to 20 from All Set
RSRP
Top 1 to 20 RSRP from All Set
RSRP0
Top 1 to 20 RSRP0 from All Set
RSRP1
Top 1 to 20 RSRP1 from All Set
RSRQ
Top 1 to 20 RSRQ from All Set
RSRQ0
Top 1 to 20 RSRQ0 from All Set
RSRQ1
Top 1 to 20 RSRQ1 from All Set
RSSI
Top 1 to 20 RSSI from All Set
RSSI0
Top 1 to 20 RSSI0 from All Set
RSSI1
Top 1 to 20 RSSI1 from All Set Top 1 to 20 Cell State from All Set
Cell State
- Serving - Neighbor
Channel Quality Info
Parameter
© Copyright by Accuver Ltd.
Description
Page 53
Tx Mode
Transmission Mode 0 – TM_INVALID 1 – TM_SINGLE_ANT_PORT0 2 – TM_TD_RANK1 3 – TM_OL_SM 4 – TM_CL_SM 5 – TM_MU_MIMO 6 – TM_CL_RANK1_PC 7 – TM_SINGLE_ANT_PORT5
PUCCH Reporting Mode
PUCCH Reporting Mode 0 – MODE_1_0 1 – MODE_1_1 2 – MODE 2_0 3 – MODE 2_1
PUSCH Reporting Mode
PUSCH Reporting Mode 0 – MODE_APERIODIC_RM12 1 – MODE_APERIODIC_RM20 2 – MODE_APERIODIC_RM22 3 – MODE_APERIODIC_RM30 4 – MODE_APERIODIC_RM31
Rank Index
Rank Index 0 – Rank 1 1 – Rank 2
WideBand CQI CW0
Wideband CQI for CW0 (Range: 0 ~ 15)
WideBand CQI CW1
Wideband CQI for CW1 (Range: 0 ~ 15)
WideBand PMI
WideBand PMI Range: 0…15 for 4 Tx, Rank 1 and 2 Range: 0…1 for 2 Tx, Rank 2 Range: 0…3 for 1 or 2 Tx, Rank 1
ML1 Downlink Info
Parameter RB Num
Description Number of DL Resource Blocks
MCS Idx0
DL MCS Index0
MCS Idx1
DL MCS Index1
Modulation Idx0 Rate
Modulation Idx1 Rate
QPSK
QPSK Num/(QPSK Num+16QAM Num+64QAM Num)*100 in TB[0]
16QAM
16QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in TB[0]
64QAM
64QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in TB[0]
QPSK
QPSK Num/(QPSK Num+16QAM Num+64QAM Num)*100 in TB[1]
16QAM
16QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in TB[1]
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
64QAM
64QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in TB[1]
ML1 Uplink Info
Parameter
Description
RB Num
Number of UL Resource Blocks
MCS Idx
UL MCS Index
Modulation Idx Rate
QPSK
QPSK Num/(QPSK Num+16QAM Num+64QAM Num)*100
16QAM
16QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100
64QAM
64QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100
Random Access Procedure
Parameter
Description
Random Access Request(MSG1)>
Preamble Sequence Index.
Preamble Sequence Random Access Request(MSG1)> Physical Root Index
Physical Root Sequence Index corresponding to Preamble Sequence
Random Access Request(MSG1)> Cyclic
Cyclic Shift
Shift Random Access Request(MSG1)>
PRACH Transmit Transmit Power (Range is -112 dBm to 23 dBm)
PRACH Tx Power Random Access Request(MSG1)> Beta
Beta PRACH (Range is 0 to 2047)
PRACH Random Access Request(MSG1)> Frequency Resource
N_ra_prb (Range is 0 to 104)
Offset Random Access Request(MSG1)>
Preamble format (based on PRACH configuration parameter signaled).
Preamble Format Random Access
System Duplex Mode
Request(MSG1)>
0: FDD
Duplex Mode
1: TDD
© Copyright by Accuver Ltd.
Page 55
Random Access Request(MSG1)> RA
Random Access Request Timing Timing - System frame number
Request Timing SFN Random Access Request(MSG1)> RA
Random Access Request Timing - Subframe number
Request Timing Sub-Fn Random Access Request(MSG1)> RA Response Window Start
Random Access Response Window Start - System frame number
SFN Random Access Request(MSG1)> RA Response Window Start
Random Access Response Window Start - Subframe number
Sub-Fn Random Access Request(MSG1)> RA Response Window End
Random Access Response Window End - System frame number
SFN Random Access Request(MSG1)> RA Response Window End
Random Access Response Window End - Subframe number
Sub-Fn Random Access Request(MSG1)> RA-
RA RNTI based on MSG1 timing
RNTI Random Access
f_ra
Request(MSG1)> Random Access
Frequency resource index 0x0: Resource reoccurring in all radio frames,
t_0_ra
Resource for TDD
0x1: Resource reoccurring in all even radio frames, 0x2: Resource reoccurring in all odd radio frames
t_1_ra
0x0: Random access resource located in first half frame 0x1: random access resource is located in second half frame UL subframe number where preamble starts 0x0: 0
t_2_ra
0x1: 1 0x2: 2 0x3: * for preamble format 4
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Density per 10 ms 0x0: 0.5 0x1: 1 d_ra
0x2: 2 0x3: 3 0x4: 4 0x5: 5 0x6: 6
Random Access Response(MSG2)> SFN
Random Access Response Timing Timing - System frame fra me number
Random Access Response(MSG2)>
Random Access Response Timing Timing - Subframe Subf rame number
Sub-Fn Random Access Response(MSG2)>
Timing Advance Value
Timing Advance Random Access Response(MSG2)> RACH Procedure Type Random Access Response(MSG2)> RACH Procedure Mode Random Access Response(MSG2)> RNTI Type
0x0 – Contention free 0x1 – Contention based
0x0 – Initial access 0x1 – Connected mode RACH procedure 0x0 – C_RNTI 0x1 – SPS_RNTI 0x2 – P_RNTI 0x3 – RA_RNTI 0x4 – TEMP_C_RNTI 0x5 – SI_RNTI 0x6 – TPC_PUSCH_RNTI 0x7 – TPC_PUCCH_RNTI 0x8 – MBMS RNTI
Random Access Response(MSG2)>
RNTI value
RNTI Value UE Identification(MSG3)>
TPC command to be applied to MSG3 transmission
TPC UE Identification(MSG3)>
Modulation and Coding Scheme
MSC UE Identification(MSG3)>
Resource Indicator Value
RIV
© Copyright by Accuver Ltd.
Page 57
UE Identification(MSG3)> CQI Enable UE Identification(MSG3)> UL Delay UE Identification(MSG3)> Hopping Flag
0x0 – Disabled 0x1 – Enabled
0x0 – Do not delay 0x1 – Delay UL transmission
0x0 – Hopping is OFF 0x1 – Hopping is ON
UE Identification(MSG3)>
System frame number of MSG3
SFN UE Identification(MSG3)>
Subframe number of MSG3
Sub-Fn UE Identification(MSG3)>
Starting resource block number of the received grant
Starting RB Num UE Identification(MSG3)>
Total number of resource blocks allocated in the grant
RB Num UE Identification(MSG3)> TB Size Index
Transport block size can be determined based on the Transport Block Size Index and Number of Resource Blocks by the log code parser
UE
0x0 – BPSK
Identification(MSG3)>
0x1 – QPSK
Modulation Type Type
0x2 – 16QAM 0x3 – 64QAM
UE Identification(MSG3)> Redundancy Version
Redundancy Version Index
index UE Identification(MSG3)>
ID of the HARQ process on which MSG3 transmission was scheduled
HARQ ID Contention Resolution(MSG4)>
System frame number of MSG4
SFN Contention Resolution(MSG4)> Sub-Fn
Subframe number of MSG4
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Contention Resolution(MSG4)> Contention Result
0x0 – Contention failed 0x1 – Contention passed
Contention Resolution(MSG4)> UL
System frame number of MSG4 ACK ACK
ACK Timing Timing SFN Contention Resolution(MSG4)> UL
Subframe number of MSG4 ACK
ACK Timing Timing Sub-Fn Sub-Fn
Radio Link Monitoring Info
Parameter Out of Sync BLER
Description Out of Sync BLER, calculated from the measured SNR. The out_sync BLER corresponds to the BLER if the actual transmission parameters equal to the parameters specified in Spec for out_sync. x / (1<<15) * 100(%)
In Sync BLER
In Sync BLER, calculated from the measured SNR. The in_sync BLER corresponds to the BLER if the actual transmission parameters equal to the parameters specified in Spec for in_sync. x / (1<<15) * 100(%)
NAS ESM Bearer Context Info
Parameter Context Type
Description 0 - Default 1 - Dedicated
Bearer ID Bearer State
ID of the bearer context 0 – INACTIVE 1 – ACTIVE 2 – ACTIVE_PENDING 3 – MODIFY
Connection ID
Connection ID associated with the bearer
SDF ID
Service Data Flow ID
LBI
Linked Bearer Identity
RB ID
© Copyright by Accuver Ltd.
Radio bearer ID that corresponds to the EPS Bearer ID of the context
Page 59
EPS QoS
Quality of Service Class Identifier 0 0 0 0 0 0 0 0 Reserved 0 0 0 0 0 0 0 1 QCI 1 0 0 0 0 0 0 1 0 QCI 2 0 0 0 0 0 0 1 1 QCI 3 0 0 0 0 0 1 0 0 QCI 4 0 0 0 0 0 1 0 1 QCI 5 0 0 0 0 0 1 1 0 QCI 6 QCI
0 0 0 0 0 1 1 1 QCI 7 0 0 0 0 1 0 0 0 QCI 8 0 0 0 0 1 0 0 1 QCI 9 0 0 0 0 1 0 1 0 Reserved to 01111111 1 0 0 0 0 0 0 0 Operator-specific QCIs to 11111110 1 1 1 1 1 1 1 1 Reserved
MBR for
Maximum bit rate for uplink
UL
(refer section 9.9.4.3 of the spec TS 24.301)
MBR for
Maximum bit rate for downlink
DL
(refer section 9.9.4.3 of the spec TS 24.301)
GBR for
Guaranteed bit rate for uplink
UL
(refer section 9.9.4.3 of the spec TS 24.301)
GBR for
Guaranteed bit rate for downlink
DL
(refer section 9.9.4.3 of the spec TS 24.301)
MBR for
Maximum bit rate for uplink (extended)
UL Ext
(refer section 9.9.4.3 of the spec TS 24.301)
MBR for
Maximum bit rate for downlink (extended)
DL Ext
(refer section 9.9.4.3 of the spec TS 24.301)
GBR for
Guaranteed bit rate for uplink (extended)
UL Ext
(refer section 9.9.4.3 of the spec TS 24.301)
GBR for
Guaranteed bit rate for downlink (extended)
DL Ext
(refer section 9.9.4.3 of the spec TS 24.301)
NAS EMM State
Parameter
Description
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
EMM State
Current EMM state EMM_NULL – 0 EMM_DEREGISTERED – 1 EMM_REGISTERED_INITIATED – 2 EMM_REGISTERED –3 EMM_TRACKING_AREA_UPDATING_INITIATED – 4 EMM_SERVICE_REQUEST_INITIATED – 5 EMM_DEREGISTERED_INITIATED –6 EMM_INVALID_STATE – 7
EMM Substate
Current EMM sub-state
MCC
MCC part of the PLMN
MNC
MNC part of the PLMN
GUTI Info
UE ID
1: IMSI_ID, 6: GUTI_ID
MCC
MCC part of the PLMN
MNC
MNC part of the PLMN
MME Group ID MME Code M-TMSI
MME_GROUP_ID interpret/display as an array of bytes.
MME Code M_TMSI interpret/display as an array of bytes.
RRC Serving Cell Info
Parameter PCI
Description Physical cell ID
EARFCN(DL)
Downlink frequency as E-ARFCN
EARFCN(UL)
Uplink frequency as E-ARFCN
Frequency(DL)
Downlink frequency of the serving cell (Unit: MHz)
Frequency(UL)
Uplink frequency of the serving cell (Unit: MHz)
Bandwidth(DL)
Downlink bandwidth 6 – 1.4 MHz 15 – 3 MHz 25 – 5 MHz 50 – 10 MHz 75 – 15 MHz 100 – 20 MHz
© Copyright by Accuver Ltd.
Page 61
Bandwidth(UL)
Uplink bandwidth 6 – 1.4 MHz 15 – 3 MHz 25 – 5 MHz 50 – 10 MHz 75 – 15 MHz 100 – 20 MHz
Cell ID TAC Band Indicator
Cell Identity received in SIB1 Tracking area code Frequency band indicator
MCC
MCC part of the PLMN
MNC
MNC part of the PLMN
Allowed Allowed Access Access
Allowed Allowed access access on the cell cell based based on network network select mode indicated indicated by NAS 0 – Full 1 – Limited
RRC PLMN Search Info
Parameter
Description
PLMN Search Request> Allowed Allowed access access on the cell cell based based on network network select mode indicated indicated by NAS NETWORK_SELECT_ MODE PLMN Search Request> SEARCH_TYPE
1 - Automatic 2 - Manual Service Search type indicated by NAS 1 – None 2 – Background Automatic 3 - Background Manual
PLMN Search Request> RAT_LIST> RAT_LIST> List[x]
1 – GSM 2 – WCDMA 3 – LTE
PLMN Search Request> PLMN_LIST> List[x] PLMN Search Response> Active RAT RAT
MCC and MNC Active Active RAT RAT 1 – GSM 2 – WCDMA 3 – LTE
PLMN Search
1 – Completed
Response>
2 – Timed out
SEARCH_STATUS
3 – Abort Confirmation 4 - Aborted
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
PLMN Search Response>
MCC and MNC
PLMN_LIST> List[x]
ML1 Serving Cell Info(Acquisition)
Parameter DL Bandwidth SFN EARFCN Frequency Serving Cell PCI PBCH Decode Result
Description Downlink bandwidth of the serving cell System frame number when PBCH was decoded EARFCN of the serving cell Frequency of the serving cell (Unit: MHz) Cell ID of the serving cell 0x1 – Success 0x0 – Failure
PHICH Duration
0 – PHICH_NORMAL 1 – PHICH_EXTENDED
PHICH Resource
HICH group multiplier 0 – 1/6 1 – 1/2 2 – 1 3 – 2
PSS Correlation
PSS correlation value of serving cell
SSS Correlation
SSS correlation value of serving cell
PBCH Reference Timing MIB Payload Frequency Offset No. of Ant
PBCH reference timing Raw PBCH payload Frequency offset estimate based upon the PBCH decode. 0x0 – 1 antenna 0x1 – 2 antennas 0x2 – 4 antennas 0x3 – Invalid
Physical Throughput
Parameter PDSCH Throughput> Total PDSCH Throughput> HARQ[#] PUSCH Throughput> Total
© Copyright by Accuver Ltd.
Description ∑PDSCH Throughput>HARQ[x] (Unit: Mbps)
(within 1 second ∑pdsch_tb_size)*8/(1sec)/(10^6) (Unit: Mbps) ∑PUSCH Throughput>HARQ[x] (Unit: Mbps)
Page 63
PUSCH Throughput> HARQ[#]
(within 1 second ∑pusch_tb_size)*8/(1sec)/(10^6) (Unit: Mbps)
MAC Throughput
Parameter DL MAC Throughput> Total DL MAC Throughput> HARQ[#] UL MAC Throughput> Total UL MAC Throughput> HARQ[#]
Description ∑DL MAC Throughput>HARQ[x] (Unit: Mbps)
(within 1 second ∑MAC DL TBS)*8/(1 sec)/(10^6) (Unit: Mbps) ∑UL MAC Throughput>HARQ[x] (Unit: Mbps)
(within 1 second ∑MAC UL GRANT(BYTE))*8/(1 sec)/(10^6) (Unit: Mbps)
RLC Throughput
Parameter DL RLC Throughput> Total DL RLC Throughput> RB CFG IDX[#]
Description ∑DL RLC Throughput>RB CFG IDX[x] (Unit: Mbps)
(∆RLC Rx Byte)*8/(∆Timestamp)/(10^6) (Unit: Mbps) Where, RLC Rx Byte = DATA_PDU_BYTES + STATUS_RXED_BYTES + INVALID_PDU_BYTES
UL RLC Throughput> Total UL RLC Throughput> RB CFG IDX[#]
∑UL RLC Throughput>RB CFG IDX[x] (Unit: Mbps)
(∆RLC Tx Byte)*8/(∆Timestamp)/(10^6) Timestamp)/(10^6) (Unit: Mbps) Where, RLC Tx Byte = NUM_NEW_DATA_PDU_BYTES + NUM_CTRL_PDU_BYTES_Tx NUM_CTRL_PDU_BYTES_Tx + NUM_RETX_PDU_BYTES NUM_RETX_PDU_BYTES
PDCP Throughput
Parameter DL PDCP Throughput> Total DL PDCP Throughput> RB CFG IDX[#]
Description ∑DL PDCP Throughput>RB CFG IDX[x] (Unit: Mbps)
(∆PDCP Rx Byte)*8/(∆Timestamp)/(10^6) (Unit: Mbps) Where, PDCP Rx Byte = NUM_DATA_PDU_RX_BYTES + NUM_CONTROL_PDU_RX_BYTES NUM_CONTROL_PDU_RX_BYTES + NUM_PDU_INVALID_BYTES NUM_PDU_INVALID_BYTES
UL PDCP Throughput> Total
∑UL PDCP Throughput>RB CFG IDX[x] (Unit: Mbps)
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
UL PDCP Throughput> RB CFG IDX[#]
(∆PDCP Tx Byte)*8/(∆Timestamp)/(10^6) (Unit: Mbps) Where, PDCP Tx Byte = NUM_DATA_PDU_TX_BYTES + NUM_CONTROL_PDU_TX_BYTES NUM_CONTROL_PDU_TX_BYTES - NUM_DISCARD_SDU_BYT NUM_DISCARD_SDU_BYTES ES
© Copyright by Accuver Ltd.
Page 65
GCT L1 Status Info L1 status information shows physical layer status such as channel setup status, serving cell information, PCH DRX and measurement periodicity, etc.
Parameter State Info> Main State
Description Physical layer main state 0: DEACTIVATED 1: IDLE 2: CONNECTED
State Info> BCH
BCH Channel State 0: RELEASE 1: SETUP
State Info> PCH
PCH Channel State 0: RELEASE 1: SETUP
State Info> DL-SCH for BCCH
DL-SCH for BCCH Channel State 0: RELEASE 1: SETUP
State Info> UL/DL-SCH and RACH
UL/DL-SCH and RACH Channel State 0: RELEASE 1: SETUP
Serving Cell Info> PCI Serving Cell Info> DL Freq Serving Cell Info> UL Freq Serving Cell Info> DL Bandwidth Serving Cell Info> UL Bandwidth Serving Cell Info> Antenna Num PCH DRX Period
Cell identifier Downlink frequency
Uplink frequency
Downlink bandwidth (Unit : RB)
Uplink bandwidth (Unit : RB)
Number of downlink transmit antenna PCH DRX periodicity 0: 0.32sec 1: 0.64sec 2: 1.28sec 3: 2.56sec 255: OFF
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Serving Cell Signal Quality Info The serving cell quality information shows SNR of reference signal (RS SNR) and received power of reference signal (RS RSSI).
Parameter
Description
RS RSSI 0
received power 0 of reference signal
RS RSSI 1
received power 1 of reference signal
RS RSSI
total received power of reference signal (rs_rssi[0] + rs_rssi[1])/2
RS SNR
reference signal power and noise power for a resource element containing RS are estimated. 10*log10{ (signal_pwr[0] + signal_pwr [1])/ (noise_pwr[0] + noise_pwr [1])})
Tx Power Info Time sync report log shows the time sync status of UE.
Parameter
Description
PUCCH Tx Power
PUSCH average UE output power in dBm
PUSCH Tx Power
PUCCH average UE output power in dBm
PRACH Tx Power
PRACH instantaneous UE output power in dBm
Total Tx Power
1 frame based average UE output power in dBm
RACH Info Parameter Frame Num TTI Preamble Format Speed Mode Root Seq Cyclic Shift Zero Correlation Zone
Description Start frame number Start subframe number 0: Format 0, 1: Format 1, 2: Format2, 3: Format3 0: normal speed, 1: high speed Root Sequence Cyclic Shift per Use Zero Correlation Zone (Ncs value 59)
Retrans Num
Retransmit number
Tx Power
RACH transmit power
Timing Adjustment Info Tx Timing adjustment log shows the TA position.
Parameter
Description
Rx SFN
Received frame number
Rx TTI
Received subframe number
© Copyright by Accuver Ltd.
Page 67
NTA NTA
Timing advance command In case of random access response : 11bit for NTA NTA In other case : 6bit for NTA (TA (TA = 0, 1, 2,..., 63)
Accum TA
Accumulate Accumulate timing timing advance advance command command
Cell Info Cell Information display cell lists which are collected from Mp Searcher and Cell Searcher.
Parameter
Description
INTRA>SYNC> RSRP
Reference Signal Received Power of Intra cell which is known the sync position.
INTRA>SYNC> RSRQ
Reference Signal Received Quality of Intra cell which is known the sync position
INTRA>SYNC> RSSI
Received Power of Intra cell which is known the sync position
INTRA>SYNC> FrameBound INTRA>SYNC> CPLength
Cell frame boundary in Intra Sync CP length in Intra Sync 0: Unknown 1 : Normal CP 2 : Extended CP
INTRA>SYNC> DL Earfcn INTRA>SYNC> Top Set
INTRA>ASYNC> RSRP INTRA> ASYNC> RSRQ INTRA> ASYNC> RSSI INTRA> ASYNC> FrameBound INTRA> ASYNC> CPLength
Earfcn number in Intra Sync PCI
PCI with RSRP strength from top 1 to 20 from Intra Sync Cell
RSRP
Top 1 to 20 RSRP from Intra Sync Cell
RSRQ
Top 1 to 20 RSRQ from Intra Sync Cell
RSSI
Top 1 to 20 RSSI from Intra Sync Cell
FrameBound
Top 1 to 20 FrameBound from Intra Sync Cell
CPLength
Top 1 to 20 CPLength from Intra Sync Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Intra Sync Cell
Reference Signal Received Power of Intra cell which is unknown the sync position. Reference Signal Received Quality of Intra cell which is unknown the sync position Received Power of Intra cell which is unknown the sync position Cell frame boundary in Intra Async CP length in Intra Async 0: Unknown 1 : Normal CP 2 : Extended CP
INTRA> ASYNC> DL Earfcn INTRA> ASYNC > Top Set
Earfcn number in Intra Async PCI
PCI with RSRP strength from top 1 to 20 from Intra Async Cell
RSRP
Top 1 to 20 RSRP from Intra Async Cell
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
INTRA>DETECT> RSRP INTRA> DETECT> RSRQ INTRA> ASYNC> RSSI INTRA> DETECT> FrameBound INTRA> DETECT> CPLength
RSRQ
Top 1 to 20 RSRQ from Intra Async Cell
RSSI
Top 1 to 20 RSSI from Intra Async Cell
FrameBound
Top 1 to 20 FrameBound from Intra Async Cell
CPLength
Top 1 to 20 CPLength from Intra Async Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Intra Async Cell
Reference Signal Received Power of Intra cell which is newly detected at this search. Reference Signal Received Quality of Intra cell which is newly detected at this search Received Power of Intra cell which is newly detected at this search Cell frame boundary in Intra Detected CP length in Intra Detected 0: Unknown 1 : Normal CP 2 : Extended CP
INTRA> DETECT> DL Earfcn INTRA> DETECT > Top Set
Earfcn number in Intra Detected PCI
PCI with RSRP strength from top 1 to 20 from Intra Detect Cell
RSRP
Top 1 to 20 RSRP from Intra Detect Cell
RSRQ
Top 1 to 20 RSRQ from Intra Detect Cell
RSSI
Top 1 to 20 RSSI from Intra Detect Cell
FrameBound
Top 1 to 20 FrameBound from Intra Detect Cell
CPLength
Top 1 to 20 CPLength from Intra Detect Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Intra Detect Cell
INTER>SYNC> RSRP
Reference Signal Received Power of Inter cell which is known the sync position.
INTER>SYNC> RSRQ
Reference Signal Received Quality of Inter cell which is known the sync position
INTER>SYNC> RSSI
Received Power of Inter cell which is known the sync position
INTER>SYNC> FrameBound INTER>SYNC> CPLength
Cell frame boundary in Inter Sync CP length in Inter Sync 0: Unknown 1 : Normal CP 2 : Extended CP
INTER>SYNC> DL Earfcn INTER >SYNC> Top Set
© Copyright by Accuver Ltd.
Earfcn number in Inter Sync PCI
PCI with RSRP strength from top 1 to 20 from Inter Sync Cell
RSRP
Top 1 to 20 RSRP from Inter Sync Cell
RSRQ
Top 1 to 20 RSRQ from Inter Sync Cell
RSSI
Top 1 to 20 RSSI from Inter Sync Cell
FrameBound
Top 1 to 20 FrameBound from Inter Sync Cell
Page 69
INTER>ASYNC> RSRP INTER> ASYNC> RSRQ INTER> ASYNC> RSSI INTER> ASYNC> FrameBound INTER> ASYNC> CPLength
CPLength
Top 1 to 20 CPLength from Inter Sync Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Inter Sync Cell
Reference Signal Received Power of Inter cell which is unknown the sync position. Reference Signal Received Quality of Inter cell which is unknown the sync position Received Power of Inter cell which is unknown the sync position Cell frame boundary in Inter Async CP length in Inter Async 0: Unknown 1 : Normal CP 2 : Extended CP
INTER> ASYNC> DL Earfcn INTER > ASYNC > Top Set
INTER>DETECT> RSRP INTER> DETECT> RSRQ INTER> ASYNC> RSSI INTER> DETECT> FrameBound INTER> DETECT> CPLength
Earfcn number in Inter Async PCI
PCI with RSRP strength from top 1 to 20 from Inter Async Cell
RSRP
Top 1 to 20 RSRP from Inter Async Cell
RSRQ
Top 1 to 20 RSRQ from Inter Async Cell
RSSI
Top 1 to 20 RSSI from Inter Async Cell
FrameBound
Top 1 to 20 FrameBound from Inter Async Cell
CPLength
Top 1 to 20 CPLength from Inter Async Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Inter Async Cell
Reference Signal Received Power of Inter cell which is newly detected at this search. Reference Signal Received Quality of Inter cell which is newly detected at this search Received Power of Inter cell which is newly detected at this search Cell frame boundary in Inter Detected CP length in Inter Detected 0: Unknown 1 : Normal CP 2 : Extended CP
INTER> DETECT> DL Earfcn INTER > DETECT > Top Set
Earfcn number in Inter Detected PCI
PCI with RSRP strength from top 1 to 20 from Inter Detect Cell
RSRP
Top 1 to 20 RSRP from Inter Detect Cell
RSRQ
Top 1 to 20 RSRQ from Inter Detect Cell
RSSI
Top 1 to 20 RSSI from Inter Detect Cell
FrameBound
Top 1 to 20 FrameBound from Inter Detect Cell
CPLength
Top 1 to 20 CPLength from Inter Detect Cell
DL Earfcn
Top 1 to 20 DL Earfcn from Inter Detect Cell
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
All Set
All Cell Cell RSRP/RSR RSRP/RSRQ/RS Q/RSSI/Fram SI/FrameBound eBound /CPLength/DL /CPLength/DL Earfcn/Cell Earfcn/Cell State State per PCI
Top Set
PCI
PCI with RSRP strength from top 1 to 20 from All Cell
RSRP
Top 1 to 20 RSRP from All Cell
RSRQ
Top 1 to 20 RSRQ from All Cell
RSSI
Top 1 to 20 RSSI from All Cell
FrameBound
Top 1 to 20 FrameBound from All Cell
CPLength
Top 1 to 20 CPLength from All Cell
DL Earfcn
Top 1 to 20 DL Earfcn from All Cell Top 1 to 20 Cell State from All Cell - Intra Sync - Intra Async
Cell State
- Intra Detect - Inter Sync - Inter Async - Inter Detect
Search Result Search Result log shows Mp Search result and Cell Search result.
Parameter MP Searcher
Description Mp Searcher Dominant Energy and Mp Searcher position per PCIS (PCIS: 0,1 or 2)
Cell Searcher> Dominant PCI
PCI with Dominant Cell Search Energy
Cell Searcher> Dominant Cell Srch
Dominant Cell Search Energy
Energy Cell Searcher> PCI#
Cell Search Energy, Energy, PCIG, PCIG, Half Frame Idx and CP Length per PCI (PCIG: 0 ~ 167, PCI: 0 ~ 503)
Earfcn Used Cell Searcher Num
EARFCN number Num of Used Cell Searcher
Channel Info The channel information shows no antenna in the 2x2 MIMO channel.
Parameter Tx Correlation> Freq Total Band(Avg) Tx Correlation> Freq Sub Band x
© Copyright by Accuver Ltd.
Description Tx Correlation in Total Band(Sub Band 1 ~ 30)
Tx Correlation per Sub Band
Page 71
Rx Correlation> Freq Total Band(Avg) Rx Correlation> Freq Sub Band x H00 (Real)> Freq Sub Band x H00 (Imaginary)> Freq Sub Band x H01 (Real)> Freq Sub Band x H01 (Imaginary)> Freq Sub Band x H10 (Real)> Freq Sub Band x H10 (Imaginary)> Freq Sub Band x H11 H11 (Real)> Freq Sub Band x H11 H11 (Imaginary)> Freq Sub Band x
Rx Correlation in Total Band(Sub Band 1 ~ 30)
Tx Correlation per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
H00 (Real value) per Sub Band
H00 (Imaginary value) per Sub Band
CQI Info The wideband CQI information shows measured CQI of wideband in the UE. The sub-band CQI information shows the CQI (channel quality information) of sub-bands. The sub-band is defined a unit for a group of resource elements used for reporting sub-band CQI.
Parameter Rank Ratio> Instant Rank Ratio> Cumulative CQI(Wideband)> Rank1 CQI CQI(Wideband)> Rank2 CW0 CQI CQI(Wideband)> Rank2 CW1 CQI CQI(Wideband)> Rank1 PMI CQI(Wideband)> Rank2 PMI CQI(Subband)> Rank1 CQI
Description Instant Rank Ratio (Range 0 ~ 1) Cumulative Rank Ratio (Range 0 ~ 1) Rank1 wide band CQI
Rank2 wide band CQI for CW0
Rank2 wide band CQI for CW1
Rank1 wide band PMI
Rank2 wide band PMI
Rank1 sub band CQI
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
CQI(Subband)> Rank2 CW0 CQI CQI(Subband)> Rank2 CW1 CQI CQI(Subband)> Rank1 PMI CQI(Subband)> Rank2 PMI
Rank2 sub band CQI for CW0
Rank2 sub band CQI for CW1
Rank1 sub band PMI
Rank2 sub band PMI
Multi-paths Profile This information shows the channel impulse response of reference signals in the time domain.
Parameter Serving PCI Ref EsNo
Description Serving cell ID (0~503) The reference EsNo is the detected RS SNR in the reference position. RS power metric of reference path. EsNo is calculated by computing 10*log10(RS power metric/noise power metric)
Ref Timing
The reference timing gives the information of reference cell timing of demodulation. Reference timing of serving cell. The resolution is Ts in a frame
Path Info[x]> EsNo Path Info[x]> Time Index
RS power metric of this path Timing offset from reference timing t iming (Ts (Ts resolution)
PBCH BLER PBCH BLER displays how much transport blocks get CRC_NOK about total received transport blocks.
Parameter Instant
Description Instant PBCH BLER (bler_info.err_nums / bler_info.total_nums) * 100
Cumulative
Cumulative PBCH BLER
PDSCH BLER PDSCH BLER displays how much transport blocks get CRC_NOK CRC_NOK about total received transport blocks.
Parameter Instant> All Instant> All
Description Instant Instant PDSCH PDSCH Total BLER BLER ((bler_info[0].err_nums + bler_info[1].err_nums) / (bler_info[0].total_nums + bler_info[1].total_nums)) * 100
Instant> Codeword #0
Instant PDSCH Codeword0 BLER (bler_info[0].err_nums / bler_info[0].total_nums) * 100
Instant> Codeword #1
Instant PDSCH Codeword1 BLER (bler_info[1].err_nums / bler_info[1].total_nums) * 100
Cumulative> All Cumulative> All
© Copyright by Accuver Ltd.
Cumulative PDSCH Total BLER
Page 73
Cumulative> Codeword #0 Cumulative> Codeword #1
Cumulative PDSCH Codeword0 BLER
Cumulative PDSCH Codeword1 BLER
PDCCH Detection Rate UE can’t calculate PDCCH BLER because UE doesn’t know when eNode -B sends its PDCCH. In other
words, UE detects PDCCH blindly. So, UE DM supports this item similar with PDCCH BLER.
Parameter
Description
DCI 0
The number of detection for DCI#0
DCI 1
The number of detection for DCI 1
DCI 1a
The number of detection for DCI 1a
DCI 1b
The number of detection for DCI 1b
DCI 1c
The number of detection for DCI 1c
DCI 2
The number of detection for DCI 2
DCI 2a
The number of detection for DCI 2a
DCI 3
The number of detection for DCI 3
DCI 3a
The number of detection for DCI 3a
DL Grant & UL Ack/Nack Status Info(Improved) DL Grant & UL ACK/NACK Status(Improved) Status(Improved) displays DL grant regardless any DCI format fo rmat in every TTI. According According to TS36.212, TS36.212, each each DCI format has the specific specific fields, fields, not not all, and the unnecessary unnecessary fields are displayed to the blank. Additionally, UL_ACK/NACK, CFI, and DCI_3/3A payload will be included in this item.
Parameter
Description
SFN
SFN value
TTI
TTI value
DCI Format> Count
DCI 1 Num/ DCI 1A Num/ DCI 1B Num/ DCI 1C Num/ DCI 2 Num/ DCI 2A Num/ DCI 3 Num/ DCI 3A Num/ N/A Num
DCI Format> Rate
DCI 1 Rate/ DCI 1A Rate/ DCI 1B Rate/ DCI 1C Rate/ DCI 2 Rate/ DCI 2A Rate/ DCI 3 Rate/ DCI 3A Rate/ N/A Rate
TM Scheme
transmission scheme 0:"SING-ANT(P0)",1:"SING-ANT(P5)",2:"TRANSDIV",3:"LARGE-CDD",4:"CLOSE-SM",5:"MU-MIMO"
TPC RB Num MCS> CW0> MCS(Idx) MCS> CW0> QPSK Rate
TPC Resource Block Number CW0 MCS CW0 QPSK Rate
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
MCS> CW0> 16 QAM Rate MCS> CW0> 64 QAM Rate MCS> CW1> MCS(Idx) MCS> CW1> QPSK Rate MCS> CW1> 16 QAM Rate MCS> CW1> 64 QAM Rate NDI> CW0> New Data Num NDI> CW0> Retrans Data Num NDI> CW0> New Data Rate NDI> CW1> New Data Num NDI> CW1> Retrans Data Num NDI> CW1> New Data Rate UL ACK/NACK> CW0> ACK Count Count UL ACK/NACK> CW0> NACK Count UL ACK/NACK> CW0> DTX Count UL ACK/NACK> CW0> ACK Rate Rate UL ACK/NACK> CW0> NACK Rate UL ACK/NACK> CW0> DTX Rate UL ACK/NACK> CW1> ACK Count Count UL ACK/NACK> CW1> NACK Count UL ACK/NACK> CW1> DTX Count UL ACK/NACK> CW1> ACK Rate Rate
© Copyright by Accuver Ltd.
CW0 16 QAM Rate
CW0 64 QAM Rate CW1 MCS CW1 QPSK Rate
CW1 16 QAM Rate
CW1 64 QAM Rate
CW0 NDI (NDI field = 1)
CW0 NDI (NDI field = 0)
New Data Num/(Retrans Data Num+New Data Num)*100 in CW0
CW1 NDI (NDI field = 1)
CW1 NDI (NDI field = 0)
New Data Num/(Retrans Data Num+New Data Num)*100 in CW1
CW0 UL ACK result
CW0 UL NACK result
CW0 UL DTX result
ACK Count/(ACK Count/(ACK Count+N Count+NACK ACK Count+D Count+DTX TX Count)*10 Count)*100 0 in CW0
NACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
DTX Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
CW1 UL ACK result
CW1 UL NACK result
CW1 UL DTX result
ACK Count/(ACK Count/(ACK Count+N Count+NACK ACK Count+D Count+DTX TX Count)*10 Count)*100 0 in CW1
Page 75
UL ACK/NACK> CW1> NACK Rate UL ACK/NACK> CW1> DTX Rate DCI 3(Mode)> DCI 3/3A Value(CW0) DCI 3(Mode)> DCI 3/3A Value(CW1)
NACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
DTX Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
CW0 DCI3/3A value
CW1 DCI3/3A value
DL Grant & UL Ack/Nack Status Info(Improved)[Detail per TTI] DL Grant & UL Ack/Nack Status Status Info(Improved)[Detail per pe r TTI] displays the related information per TTI.
Parameter
Description
SFN
SFN value
TTI
TTI value
CFI
CFI value
DCI Format
DCI format 0:"DCI_1",1:"DCI_1A,2:"DCI_1B",3:"DCI_1C",4:"DCI_2", 5:"DCI_2A",6:"DCI_3",7:"DCI_3A"
RNTI
RNTI type 0:"C-RNTI",1:"RA-RNTI",2:"P-RNTI",3:"SI-RNTI", 0:"C-RNTI",1:"RA-RNTI",2:"PRNTI",3:"SI-RNTI", 4:"PUCCH",5:"PUSCH",6:"S 4:"PUCCH",5:"PUSCH",6:"SPSPSRNTI",7:”T-CRNTI”
TM Scheme
transmission scheme 0:"SING-ANT(P0)",1:"SING-ANT(P5)",2:"TRANS0:"SING-ANT(P0)",1:"SING -ANT(P5)",2:"TRANS- DIV",3:"LARGE-CDD",4:"CLO DIV",3:"LARGE-CDD",4:"CLOSESESM",5:"MU-MIMO"
Distribution Flag
distribution flag 0:"LOCAL", 1:"DIST"
Gap Value
gap value
RA Header
RA header
Precoding
precoding information
RB Num PMI Confirmation TPC HARQ Number
Resource Block Number PMI confirmation TPC HARQ number
MCS(CW0)
MCS in CW0
NDI(CW0)
NDI in CW0
RV(CW0)
redundancy version in CW0
MOD Type(CW0) New/Retrans Type(CW0) TB Size(CW0) CRC Result(CW0)
modulation type in CW0 new or retransmission type in CW0 transport block size in CW0 CRC result in CW0
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
UL ACK/NACK Result(CW0)
UL ACK/NACK ACK/NACK result in CW0
DCI 3(CW0)
DCI3/3A value in CW0
MCS(CW1)
MCS in CW1
NDI(CW1)
NDI in CW1
RV(CW1)
redundancy version in CW1
MOD Type(CW1) New/Retrans Type(CW1) TB Size(CW1) CRC Result(CW1) UL ACK/NACK Result(CW1) DCI 3(CW1)
modulation type in CW1 new or retransmission type in CW1 transport block size in CW1 CRC result in CW1 UL ACK/NACK ACK/NACK result in CW1 DCI3/3A value in CW1
UL Grant & DL Ack/Nack Status Info UL Grant Info Status log shows get UL Scheduling Grant information to PDCCH.
Parameter
Description
SFN
SFN value
TTI
TTI value
FH> FH Num FH> No FH Num FH> FH Rate MCS> CQI REQ> MCS(Idx) MCS> No CQI REQ> MCS(Idx) MCS> No CQI REQ> QPSK Rate MCS> No CQI REQ> 16 QAM Rate MCS> No CQI REQ> 64 QAM Rate
FH Number No FH Number FH Num/(No FH Num+FH Num)* 100 No CQI Request Modulation and Coding Rate
CQI Request Modulation and Coding Rate
QPSK Num/(QPSK Num+16QAM Num+64QAM Num)*100 in CQI Request
16QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in CQI Request
64QAM Num/(QPSK Num+16QAM Num+64QAM Num)*100 in CQI Request
New Data Num
New data indicator (NDI field = 1)
Retrans Data Num
New data indicator (NDI field = 0)
New Data Rate TPC CS DMRS DL ACK/NACK> ACK Count
© Copyright by Accuver Ltd.
New Data Num/(Retrans Data Num+New Data Num)*100 Power control of PUSCH Cyclic shift for DMRS DL ACK result
Page 77
DL ACK/NACK> NACK Count DL ACK/NACK> DTX Count DL ACK/NACK> ACK ACK/NACK> ACK Rate DL ACK/NACK> NACK Rate DL ACK/NACK> DTX Rate
DL NACK result
DL DTX result
ACK Count/(ACK Count/(ACK Count+N Count+NACK ACK Count+D Count+DTX TX Count)*10 Count)*100 0
NACK Count/(ACK Count+NACK Count+DTX Count)*100
DTX Count/(ACK Count+NACK Count+DTX Count)*100
UL Grant & DL Ack/Nack Status info[Detail per TTI] UL Grant & DL Ack/Nack Status info[Detail per TTI] displays the related information per TTI.
Parameter
Description
SFN
SFN value
TTI
TTI value
TB Size RB Assign FH
Transport Block size Resurce block assingment 0 :No FH 1 :FH
MCS
Modulation and Coding Rate
NDI
New data indicator
TPC
Power control of PUSCH
CS DMRS CQI Request Ind
Cyclic shift for DMRS CQI Request Indication 0 : No CQI Request 1 : CQI Request
DL ACK/NACK Result
0 :NACK 1 :ACK
PDSCH PHY Throughput PDSCH PHY Throughput has displays how much to get the downlink data in 1sec.
Parameter All
Description PDSCH PDSCH PHY Total Throughput Throughput (cw_0 + cw_1) / 1000
Codeword #0
PDSCH PHY Codeword0 Throughput (cw_0) / 1000
Codeword #1
PDSCH PHY Codeword0 Throughput (cw_1) / 1000
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
UL PRB MAP Data Info This information shows the log of transmit physical resource mapping information.
Parameter
Description
SFN
Frame number
TTI
TTI number
Bandwidth
0:1.4MHz, 1:3MHz, 2:5MHz, 3:10MHz, 4:15MHz, 5:20MHz
Channel Type> Count
DTX/ PRACH/ PUCCH/ PUSCH/ SRS/ PUSCH+SRS/ PUCCH+SRS Count
Channel Type> Rate
DTX/ PRACH/ PUCCH/ PUSCH/ SRS/ PUSCH+SRS/ PUCCH+SRS Rate
PRACH
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PRACH
PUCCH
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUCCH
PUSCH
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUSCH
SRS
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in SRS
PUSCH+SRS
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUSCH+SRS
PUCCH+SRS
RB Size/ Even Slot RB Offset/ Odd Slot RB Offset/ SRS RB Size/ SRS RB Offset in PUCCH+SRS
PUSCH PHY Throughput UL Throughput log shows the Uplink data throughput at UE side.
Parameter NEW Transmission
Description A number of bits about new transmission per 1 sec (new_bit_nums) / 1000
Total UL
A number of bits about re-transmission per 1 sec (new_bit_nums + retrans_bit_nums) / 1000
L2 DL Throughput Parameter PDCP> Total
Description Total Downlink Downli nk PDCP Throughput Throug hput (∑rbId total Byte*8/1000)
PDCP> RB ID(x)
Downlink PDCP Throughput per RB ID (rbId total Byte*8/1000)
RLC> Total
Total Downlink RLC Throughput (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM), 4 ~ 5 (UM)
© Copyright by Accuver Ltd.
Page 79
RLC> AM> RLC> AM> Total
Total Downlink Downlink RLC AM Throughpu Throughputt (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> AM> RLC> AM> RB RB ID(x) ID(x)
Downlink Downlink RLC RLC AM Throughpu Throughputt per RB RB ID (rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> UM> Total
Total Downlink Downli nk RLC UM Throughput Throug hput (∑rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
RLC> UM> RB ID(x)
Downlink RLC UM Throughput per RB ID (rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
MAC
Downlink MAC Throughput (MacDlTotalBytes*8/1000)
L2 UL Throughput Parameter PDCP> Total
Description Total Uplink Uplin k PDCP Throughput Throug hput (∑rbId total Byte*8/1000)
PDCP> RB ID(x)
Uplink PDCP Throughput per RB ID (rbId total Byte*8/1000)
RLC> Total
Total Uplink Uplin k RLC Throughput Throug hput (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM), 4 ~ 5 (UM)
RLC> AM> RLC> AM> Total
Total Uplink Uplink RLC RLC AM Throughpu Throughputt (∑rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> AM> RLC> AM> RB RB ID(x) ID(x)
Uplink RLC AM Throughput Throughput per RB ID (rbId total Byte*8/1000) Precondition: index 1 ~ 3 (AM)
RLC> UM> Total
Total Uplink Uplin k RLC UM Throughput Throug hput (∑rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
RLC> UM> RB ID(x)
Uplink RLC UM Throughput per RB ID (rbId total Byte*8/1000) Precondition: index 4 ~ 5 (AM)
MAC
Uplink MAC Throughput (MacUlTotalBytes*8/1000)
PDSCH MAC BLER This item is for MAC BLER of downlink (PDSCH). Ratio of transport blocks which remain un-
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
acknowledged (CRC failure) after HARQ retransmission divided by total number of initial transmissions received by UE MAC
Parameter Instant> All Instant> All
Description Instant Instant total total MAC MAC BLER ( (cwd0ErrNum/cwd0TBNum) *100 + (cwd1ErrNum/cwd1TBNum) *100 ) / 2
Instant> Codeword #0
Instant code word #0 MAC BLER (cwd0ErrNum/cwd0TBNum) *100
Instant> Codeword #1
Instant code word #1 MAC BLER (cwd1ErrNum/cwd1TBNum) *100
Cumulative> All Cumulative> All Cumulative> Codeword #0 Cumulative> Codeword #1
Cumulative total MAC BLER Cumulative code word #0 MAC BLER
Cumulative code word #1 MAC BLER
RLC States Info This item provides state information of RLC Tx/Rx Entity.
Parameter Tx States> RB ID (x)> Mode Tx States> RB ID (x)> State Rx States> RB ID (x)> Mode Rx States> RB ID (x)> State
Description Tx States RLC Mode (AM /UM/TM)
Tx States RLC Tx Entity state (NULL/DTR)
Rx States RLC Mode (AM /UM/TM)
Rx States RLC Tx Entity state (NULL/DTR)
MAC State Info This item includes MAC DL/UL state information.
Parameter MAC UL State
Description Current state of MAC uplink (0-NOT_CONFIGURED, (0-NOT_CONFIGURED, 1-CONFIGURED, 2-OUT_OF_SYNC, 3-IN_SYNC, 44IN_CR, 5-READY_TO_SCHED )
MAC DL State
Current State of MAC downlink (0-NOT_CONFIGURED, 1-CONFIGURED, 2-PCH_STATE, 3-RACH_STATE, 4DSCH_STATE)
MAC UL Transmission Info This item is for total packets information of uplink data transmission.
© Copyright by Accuver Ltd.
Page 81
Parameter Count> 1st Trans
Description Success in 1st transmission
Count> 1st Re-Trans
Success in 1st re-transmission
Count> 2nd Re-Trans
Success in 2nd re-transmission
Count> 3rd Re-Trans
Success in 3rd re-transmission
Count> 4th Re-Trans
Success in 4th re-transmission
Count> 5th Re-Trans
Success in 5th re-transmission
Count> 6th Re-Trans
Success in 6th re-transmission
Count> 7th Re-Trans
Success in 7th re-transmission
Count> 8th Re-Trans
Success in 8th re-transmission
Count> 9th Re-Trans
Success in 9th re-transmission
Count> 10th Re-Trans
Success in 10th re-transmission
Count> Total Trans
∑SuccessCnt i (Where, i = 0 to 10)
Count> Bad Count
Bad Count
Percentage> 1st Trans Percentage> 1st ReTrans Percentage> 2nd ReTrans Percentage> 3rd ReTrans Percentage> 4th ReTrans Percentage> 5th ReTrans Percentage> 6th ReTrans Percentage> 7th ReTrans Percentage> 8th ReTrans Percentage> 9th ReTrans Percentage> 10th ReTrans Percentage> Total Trans Percentage> Bad Percentage
1st Trans/(Total Trans/(Total Trans+Bad Count)*100 1st Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
2nd Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
3rd Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
4th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
5th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
6th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
7th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
8th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
9th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100
10th Re-Trans/(Total Re-Trans/(Total Trans+Bad Count)*100 Total Trans/(Total Trans+Bad Count)*100 Bad Count/(Total Trans+Bad Count)*100
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
RACH REQ Info This item includes RACH request information.
Parameter
Description
RACH Transmit Time
RACH transmit time
Retransmission Num
Retransmission Num
RACH Type
0 : INITIAL 1 : HANDOVER 2 : UL DATA ARRIVAL 3 : DL DATA ARRIVAL 4 : SR MAX 5 : NO_SR_CONFIG
RA-RNTI Preamble ID
RACH RNTI Preamble Identity
RACH RSP General Info This item includes RACH response information.
Parameter RACH Response Receiving Time Result RACH Preamble Identity BackOff Indicator Time Advance Temporary C-RNTI MCS TPC for scheduled PUSCH Hopping Flag UL Delay CQI Request Resource Block Assignment Assignment Access Access RACH RACH Latency Latency
Description RACH response receiving time 0: NACK, 1: ACK RACH Preamble Identity BackOff Indicator Time Advance Temporary C-RNTI Modulation and coding Scheme TPC command for scheduled PUSCH Hopping Flag UL Delay CQI Request Resource block assignment(10bits) Access Access RACH RACH Latency Latency (sec) (sec)
RNTI Info This item includes RNTI information.
Parameter C-RNTI
© Copyright by Accuver Ltd.
Description C-RNTI
Page 83
RA-RNTI Temporary empora ry C-RNTI
RA-RNTI Temporary empor ary C-RNTI
Serving Cell & Neighbor Cell Lists Parameter Serving Cell Info> UE State
Description Current UE state - UE_IDLE_MODE - UE_CONNECTED_MODE UE_CONNECTED_MODE - NO_SERVICE - NON_LTE_RAN
Serving Cell Info> Freq UL Serving Cell Info> Freq DL
Uplink Carrier Frequency
Downlink Carrier Frequency
Serving Cell Info> PCI
Physical Cell Identity
Serving Cell Info> TAC
Tracking Area Code
Serving Cell Info> PLMN Identity Serving Cell Info> Global Cell ID Intra Freq Cell Lists> DL Freq
PLMN Identity
Global Cell ID
Downlink Carrier Frequency
Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving PCI
PCI Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving RSRP
RSRP Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving RSRQ
RSRQ Intra Freq Cell Lists> Serving Cell> Serving
Intra Freq Cell Serving RSSI
RSSI Intra Freq Cell Lists> Serving Cell> All Cell> All Cell Cell
Intra Freq Cell Serving RSRP/RSSQ/RSSI per PCI
Info Intra Freq Cell Lists> Monitored Cell> Monitored Cell Count
Number of Monitored PCI from Intra Freq Cell
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
Intra Freq Cell Lists> Monitored Cell>
Monitored PCI List from Intra Freq Cell
Monitored Cell List Intra Freq Cell Lists> Monitored Cell> Summary Monitored
Monitored PCI List with (RSRP,RSRQ) (RSRP,RSRQ) from Intra Freq Cell
Cell List Intra Freq Cell Lists> Monitored Cell> RSRP Intra Freq Cell Lists> Monitored Cell> RSRQ Intra Freq Cell Lists> Monitored Cell> RSSI Intra Freq Cell Lists> Monitored Cell> Top Set
Intra Freq Cell Monitored RSRP per PCI
Intra Freq Cell Monitored RSRQ per PCI
Intra Freq Cell Monitored RSSI per PCI PCI
PCI with RSRP strength from top 1 to 20 from Intra Freq Monitored Cell
RSRP
Top 1 to 20 RSRP from Intra Freq Monitored Cell
RSRQ
Top 1 to 20 RSRQ from Intra Freq Monitored Cell
RSSI
Top 1 to 20 RSSI from Intra Freq Monitored Cell
Intra Freq Cell Lists> Detected Cell> Detected
Number of Detected PCI from Intra Freq Cell
Cell Count Intra Freq Cell Lists> Detected Cell> Detected
Detected PCI List from Intra Freq Cell
Cell List Intra Freq Cell Lists> Detected Cell> Summary Detected Cell
Detected PCI List with (RSRP,RSRQ) (RSRP,RSRQ) from Intra Freq Cell
List Intra Freq Cell Lists> Detected Cell> RSRP Intra Freq Cell Lists> Detected Cell> RSRQ Intra Freq Cell Lists> Detected Cell> RSSI Intra Freq Cell Lists> Detected Cell> Top Set
Intra Freq Cell Lists> Lists> All All Set Intra Freq Cell Lists> Top Set
© Copyright by Accuver Ltd.
Intra Freq Cell Detected RSRP per PCI
Intra Freq Cell Detected RSRQ per PCI
Intra Freq Cell Detected RSSI per PCI PCI
PCI with RSRP strength from top 1 to 20 from Intra Freq Detected Cell
RSRP
Top 1 to 20 RSRP from Intra Freq Detected Cell
RSRQ
Top 1 to 20 RSRQ from Intra Freq Detected Cell
RSSI
Top 1 to 20 RSSI from Intra Freq Detected Cell
Intra Freq Cell RSRP/RSRQ/RSSI/C RSRP/RSRQ/RSSI/Cell ell State per PCI PCI
PCI with RSRP strength from top 1 to 20 from Intra Freq Cell
RSRP
Top 1 to 20 RSRP from Intra Freq Cell
RSRQ
Top 1 to 20 RSRQ from Intra Freq Cell
RSSI
Top 1 to 20 RSSI from Intra Freq Cell
Page 85
Top 1 to 20 Cell State from Intra Freq Cell Cell State
- Serving - Monitored - Detected
Inter Freq Cell Lists> Freq DL(x)>PCI(y)>
Inter frequency cell Reference Signal Received Power
RSRP Inter Freq Cell Lists> Freq DL(x)>PCI(y)>
Inter frequency cell Reference Signal Received Quality
RSRQ Inter Freq Cell Lists> Freq DL(x)>PCI(y)>
Inter frequency cell Received Power
RSSI Inter Freq Cell Lists> Freq DL(x)>PCI(y)> Cell Type
Inter frequency cell type 1 : monitored cell 2 : detected cell
NAS System Info Parameter PLMN_ID TAC
Description PLMN ID of the current cell TAC of the current cell
Cell ID
Cell ID of the current cell
TAI List
Tracking Area identity List MCC (Mobile Country Code), MNC (Mobile Network Code) and TAC (Tracking (Tracking Area Code).
RRC BCH Status Info This item provides the information of BCH status.
Parameter RRC BCH Status> PCI
Description Physical Cell Identity (0~503)
RRC BCH Status> Freq DL
DL Frequency
RRC BCH Status> Purpose
Purpose of BCH Setup - SIB_NORMAL, - CELL_RESELECTION, - SIB_MODIFICATION, - MOVE_TO_IDLE, MOVE_TO_IDLE, - SIB_CONNECTED, - SFN_READ, - SPECIFIED_SIB, - SIBC_SIB
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
RRC BCH Status> Result
Result of receiving System Information. - SUCCESS, - PLMN_MISMATCH, - MIB_TIMEOUT, - SI_TIMEOUT, - LAST_RESULT
NAS State Info This item provides the state information of EMM (EPS Mobility Management), ECM (EPS Connection Management) and PLMN and EU (EPS Update) status when each state is changed.
Parameter
Description
EMM State
Current state of EMM (EPS Mobility Management)
ECM State
Current state of ECM (EPS Connection Management)
PLMN State
Current state of PLMN
EU State
Current EU (EPS Update) status
NAS State Info(R4) This item provides the NAS state information of EMM (EPS Mobility Management), ECM (EPS Connection Management) and PLMN and EMM Cache status when each state is changed.
Parameter
Description
EMM State
Current state of EMM (EPS Mobility Management)
ECM State
Current state of ECM (EPS Connection Management)
PLMN State
Current state of PLMN
EMM Cache State
Current state of EMM Cache
Radio & NAS Signaling Failure Info Parameter Radio Problem Cause NAS Signaling Failure Cause
Description Radio problem diagnostic logging attribute. NAS signaling failure diagnostic logging attribute
RRC Freq Scan Info This item displays the result of frequency scan.
Parameter Search Type Type
Description Cell Search Method - Frequency LIST - Frequency RANGE
© Copyright by Accuver Ltd.
Page 87
Freq DL RSRP
DL Frequency Reference Signal Received Power
Cell Reselection Info This item provides the information on both source cell and target cell when RRC perform cell reselection.
Parameter Old Freq DL Old Cell ID New Freq DL New Cell ID
Description Old Carrier Frequency Old Cell Identity New Carrier Frequency New Cell Identity
Handover History This item displays handover history, delay and result.
Parameter
Description
Source Cell
Source Cell Physical Identity
Target Cell
Target Cell Physical Identity
Handover Delay
Handover delay (Unit : ms)
Result
- FAIL - SUCCESS
Handover Hando ver Type
- LTE - Outbound IRA I RAT T - Inbound IRAT IRAT
Data Path Packet Loss This item is for UL/DL packet loss of data path(HIM/PDCP/L2).
Parameter
Description
UL UsbBlockTime
UL : USB Blocking count
UL SdioBlockTime
UL : SDIO Blocking count
UL UsbUnreg
UL : number of discarded packet in USB by unregistered connection
UL SdioUnreg
UL : number of discarded packet in SDIO by unregistered connection
UL HimAllocFail
UL : Memory allocation fail count in HIM
UL DimInvHdr
UL : Number of discarded packet in DIM by Invalid header
UL DimNoRB
UL : Number of discarded packet in DIM because of no RB
UL PdcpSduFull
UL : Fail count in PDCP by PDCP SDU Queue full
UL PdcpPduBufFull
UL : Number of discarded packet in PDCP by PDCP PDU Queue full
UL PdcpCipAllocFail
UL : Number of discarded packet in PDCP by Ciphering block full
UL PdcpDisTimer
UL : Number of discarded packet by PDCP discard timer expiry
UL MacSchedMiss
UL : Number of discarded MAC PDU which is not transfered
XCAP-LTE Analyzer Parameter Description/Ed.04 Description/Ed.04
DL PhyAllocFail DL MacInvHdr DL RlcDuplication DL RlcInvHdr
DL : Number of discarded MAC PDU by memory allocation in L1 DL : Number of discarded MAC PDU by invalid MAC header DL : number of discarded RLC PDU by duplication DL : number of discarded RLC PDU by invalid RLC header
DL RlcOutWnd
DL: number of discarded RLC PDU which falls outside of window
DL RlcRsmFull
DL : number of discard RLC PDU by RSM buffer full
DL PdcpInvHdr
DL : number of discarded PDCP PDU by invalid PDCP header
DL PdcpOutWnd DL CipAllocFail DL DimInvalid DL HimIfFull
DL : number of discarded PDCP PDU which falls outside of window DL : Number of discarded packet in PDCP by Ciphering block full DL : Number of discarded packet in DIM by IP Header length mismatch DL : Number of discarded packet in HIM by interface buffer full
DL UsbBlockTime
DL : USB block count
DL SdioBlockTime
DL : SDIO block count
DL UsbPacketLoss
DL : number of discarded packet in USB
DL SdioPacketLoss
DL : number of discard packet in SDIO
ESM Instance Info This item includes ESM instance information R3. Maximum number of ESM instance is 15(1~15). The EPS Id uniquely identifies each ESM instance.
Parameter Tab Index EPS Id
Description st
nd
1: 1 tab, 2: 2
Linked Bearer ID
PDN Address
PDN IP Address
QCI EPS Type
th
tab
EPS ID
Linked Bearer Id
APN
tab, … 15: 15
Access Access Point Name QCI (1 ~ 9) - NONE BEARER TYPE - DEFAULT_BEARER - DEDICATED_BEARER
ESM State
- DEACTIVE - ACTIVE
PTI Instance Id
© Copyright by Accuver Ltd.
PTI Instance ID
Page 89
Deactivate Mode
- NONE_MODE - NORMAL - NORMAL_ALL - DETACH - STATUS_IND - PDN_DISCONNECT - PDN_DISCONNECT_REJECT PDN_DISCONNECT_REJECT - PDN_DISCONNECT_TIMEOUT PDN_DISCONNECT_TIMEOUT - MODIFICATION_REJECT - MODIFICATION_TIMEOUT - OVERWRITE - LOCALLY
Overwrite Mode
- NONE BEARER TYPE - DEFAULT_BEARER - DEDICATED_BEARER