Ope per rator or’’s Ma Manu nua al
DD310-26 1.
INTRODUCTION TO MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.
2.
Intended to use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
1.2. Recommended operating conditions . . . . . . . . . . . . . . .
5
1.3. Components of the machine . . . . . . . . . . . . . . . . . . . . . .
6
SAFETY & ENVIRONMENTAL INSTRUCTIONS . . . . . . . . . . . . .
16
2.1. 2.1. Oper Operat ator or sa saffety ety ins insttruct ructiions ons . . . . . . . . . . . . . . . . . . . . . . .
16
2.2. 2.2. Main ain sa saffety ety haza hazard rds s in use use or mai mainten ntenan ance ce wor work . . . . .
17
2.3. 2.3. Envir nviron onme men ntal tal prec precau auttions ons . . . . . . . . . . . . . . . . . . . . . . .
19
2.4. 2.4. Type ype pl plate ate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
2.5. 2.5. Gradie adient nt angl angle e ..................................
20
2.6. 2.6. Safet afety y tel teles esco copi pic c can cano opy . . . . . . . . . . . . . . . . . . . . . . . . .
21
2.7. 2.7. Mac achi hine ne in tramm amming posi positi tion on and and par parkin king . . . . . . . . . .
22
2.8. 2.8. Dange angerr ar area eas s ...................................
23
2.8.1. 2.8 .1.
Danger Danger are area a when when trammin tramming g .............................
23
2.8.2. 2.8 .2.
Danger Danger are area a when when drillin drilling. g. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
2.9. 2.9. Cond Condit itio ions ns in whi which the rig shou should ld not not be use used d .......
25
2.10 2.10.. Nois Noise e lev level el and and noi noise se emis emissi sion on . . . . . . . . . . . . . . . . . . . .
25
2.11 2.11.. Acce Accele lera rati tion on va valu lue e . .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
25
2.12 2.12.. Sa Safe fety ty equi equipm pmen entt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
2.13 2.13.. Fire Fire prev preven enti tion on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
2.13.1. 2.13.1. Refilling Refilling fuel. fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 (94)
5
26
2.14 2.14.. Fire Fire ex exti ting ngui uish sher er (opt (optio iona nal) l) . . . . . . . . . . . . . . . . . . . . . . .
27
2.15. Emergency Emergency stops, stops, main switches switches and emergency emergency brakes brakes
28
2.16 2.16.. El Elec ectr tric ic ca cabl ble e . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
30
78494380 - 05-06-2007 SR-RB-FL
DD310-26 1.
INTRODUCTION TO MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.
2.
Intended to use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
1.2. Recommended operating conditions . . . . . . . . . . . . . . .
5
1.3. Components of the machine . . . . . . . . . . . . . . . . . . . . . .
6
SAFETY & ENVIRONMENTAL INSTRUCTIONS . . . . . . . . . . . . .
16
2.1. 2.1. Oper Operat ator or sa saffety ety ins insttruct ructiions ons . . . . . . . . . . . . . . . . . . . . . . .
16
2.2. 2.2. Main ain sa saffety ety haza hazard rds s in use use or mai mainten ntenan ance ce wor work . . . . .
17
2.3. 2.3. Envir nviron onme men ntal tal prec precau auttions ons . . . . . . . . . . . . . . . . . . . . . . .
19
2.4. 2.4. Type ype pl plate ate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
2.5. 2.5. Gradie adient nt angl angle e ..................................
20
2.6. 2.6. Safet afety y tel teles esco copi pic c can cano opy . . . . . . . . . . . . . . . . . . . . . . . . .
21
2.7. 2.7. Mac achi hine ne in tramm amming posi positi tion on and and par parkin king . . . . . . . . . .
22
2.8. 2.8. Dange angerr ar area eas s ...................................
23
2.8.1. 2.8 .1.
Danger Danger are area a when when trammin tramming g .............................
23
2.8.2. 2.8 .2.
Danger Danger are area a when when drillin drilling. g. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
2.9. 2.9. Cond Condit itio ions ns in whi which the rig shou should ld not not be use used d .......
25
2.10 2.10.. Nois Noise e lev level el and and noi noise se emis emissi sion on . . . . . . . . . . . . . . . . . . . .
25
2.11 2.11.. Acce Accele lera rati tion on va valu lue e . .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
25
2.12 2.12.. Sa Safe fety ty equi equipm pmen entt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
2.13 2.13.. Fire Fire prev preven enti tion on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
2.13.1. 2.13.1. Refilling Refilling fuel. fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 (94)
5
26
2.14 2.14.. Fire Fire ex exti ting ngui uish sher er (opt (optio iona nal) l) . . . . . . . . . . . . . . . . . . . . . . .
27
2.15. Emergency Emergency stops, stops, main switches switches and emergency emergency brakes brakes
28
2.16 2.16.. El Elec ectr tric ic ca cabl ble e . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
30
78494380 - 05-06-2007 SR-RB-FL
DD310-26 3.
4.
5.
CHECKS AND INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .
31
3.1. Assembly an and ch checking of of a new ma machine . . . . . . . . . . .
31
3.2. 3.2. Rout outine ine chec checks ks bef before ore star startting ing a shif shiftt . . . . . . . . . . . . . .
32
3.3. 3.3. Star tardar dard elec electtric ca cabi bine nett . . . . . . . . . . . . . . . . . . . . . . . . .
40
3.4. 3.4. All Allen brad bradlley elec electtric ric cab cabin inet et . . . . . . . . . . . . . . . . . . . . . .
41
3.5. 3.5. Tra ram mming ing com compar partmen ment . . . . . . . . . . . . . . . . . . . . . . . . . .
42
3.6. 3.6. Boom oom move moveme ment nts s ...............................
45
3.7. 3.7. Dril Drilli ling ng com compar partmen tmentt . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
TRA TRAMM MMIING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
4.1. 4.1. Star tarting ing the engi engine ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
4.2. 4.2. Emer mergen gency cy/p /par arki king ng brak brake e tes estt . . . . . . . . . . . . . . . . . . . . .
54
4.3. 4.3. Elect lectri ric c cab cable le . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
4.4. 4.4. Movi oving the the mac achi hine ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
4.5. 4.5. Par arki king ng the the mac machi hin ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
DRIL DRILLI LING NG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
58
5.1 5.1. Se Settting ing-up -up the mac achi hine ne in the the drift rift . . . . . . . . . . . . . . . . .
58
5.2. 5.2. Elect lectrric pow power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
5.3. 5.3. Par aral alle lellism ism se sett ttiing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
5.4. 5.4. Se Settting ting dril drilll fee eed d TTF and and TFX TFX . . . . . . . . . . . . . . . . . . . . .
68
5.5. 5.5. Colla ollarring ing a hol hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
5.6. 5.6. Norma ormall dri drillin lling g
.................................
70
5.7. 5.7. Rod unco uncoup upli ling ng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
5.8. 5.8. Endin nding g a shi shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
78494380 - 05-06-2007 SR-RB-FL
3 (94)
DD310-26 6.
7.
4 (94)
TRANSPORTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
6.1. Transportation on a platform . . . . . . . . . . . . . . . . . . . . . .
72
6.2. Towing the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
6.3. Lifting the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
6.4. Storing the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
78494380 - 05-06-2007 SR-RB-FL
DD310-26 1.
INTRODUCTION TO MACHINE
INTRODUCTION TO MACHINE
This manual provides instructions for the use and safe operation of an DD310-26 machine.The information contained in this manual must be studied and thoroughly assimilated before attempting to operate this machine. NOTE: Whenever FRONT, REAR, RIGHT and LEFT are mentioned throughout this manual, it is assumed that the operator is standing at the rear of the machine (Engine end) and looking toward the front (Boom end). Right and left DO NOT REFER to the operator’s seat but refer to the right and left of the machine.
RIGHT
REAR
FRONT LEFT
WARNING
1.1.
Danger. It is the operator’s responsibility to ensure that the machine is in perfect working condition. At each machine start-up, a pre-start check list MUST be completed even if the machine has been used earlier in the day. It is the operator who is at the controls that will assume full responsibility if an accident or injury occurs.
Intended to use
DD310-26 is intended for use in mining, preparation work and tunneling.It is an independently operating hydraulic rig that drills vertical, inclined and horizontal holes.
1.2.
Recommended operating conditions
Ambient temperature -30°C .... +50°C. • Maximum altitude from sea level 3000m. • Before use in exceptional conditions, contact Sandvik’s engineering department.
78494380 - 05-06-2007 SR-RB-FL
5 (94)
DD310-26
INTRODUCTION TO MACHINE
1.3.
Components of the machine FRONT SECTION
FRONT SECTION
1
2
1. Rock drill 2. Feed 3. Boom 4. Front stabilizers
3 4
ROCK DRILL
1 HLX5
4 3
1. Pressure accumulator 2. Rotation housing 3. Flushing housing 1
4. Gear housing
2 3
4
HL510
2
1
6 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
INTRODUCTION TO MACHINE
DRILL FEED
1 2
3 4
TF500
1 2 3 4
1. Hose reel 2. Rock drill carriage 3. Feed cylinder, wire ropes
TTF500
4. Centralizers
3
4
1 2 TFX500
78494380 - 05-06-2007 SR-RB-FL
7 (94)
DD310-26
INTRODUCTION TO MACHINE
BOOM
B26F Boom Swing Boom Extension Divergence
Feed Swing
Feed Extension
Boom Lift
(main)
Feed Swing (slave)
Feed Tilt
Feed Roll-over
Ensure horizontal // Ensure vertical //
B26NV-XLNV
Boom Swing Boom Extension
Feed Roll-over
Feed Extension
Boom Lift Feed Swing (main)
Feed Swing (slave)
Feed Tilt Divergence Feed Angle
Ensure horizontal // Ensure vertical //
8 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
INTRODUCTION TO MACHINE
MIDDLE SECTION MIDDLE SECTION
3b
3a 1. Tramming compartment 2. Drilling compartment 3a. Air circuit components b.
Mine air supply (optional)
4. Tramming power train 5. Drilling hydraulic components
5 1
6
5
2
6. Telescopic safety canopy 7. Water Hose reel (optional)
7
8. Fire extinguisher (optional)
4
8
TRAMMING COMPARTMENT
1. Steering wheel
5 2
7
2. Tramming control panel 3
3. Stabilizers and canopy controls 8
4. Tramming control pedals 5. Emergency brake push button 6. Operator seat 7. Tramming test point 8. Cable reel (and water hose reel optional) electric control
1
9. Safety Belt 4
6
78494380 - 05-06-2007 SR-RB-FL
9
9 (94)
DD310-26
INTRODUCTION TO MACHINE
DRILLING COMPARTMENT
4
7
1
4
8
3 6 5
4
9
3
7
2
1
4
8
10 6 5
3
2
1. Boom controls
7. Indictor light Panel
2. Drilling controls
8. Optional lever for boom movement (B26 NV or LC) or rod clamp
3. Drilling pressure adjustments 4. Gauges 5. Switches and light 6. Emergency stop push button
10 (94)
9.Optional lever for rod clamp 10.Optional lever for TRS
78494380 - 05-06-2007 SR-RB-FL
DD310-26
INTRODUCTION TO MACHINE
TELESCOPIC SAFETY CANOPY
1
2
1. Courtesy light (optional) 2. Flashing light (optional) 3. Courtesy & flashing light electric switches (optional)
3
TRAMMING POWER TRAIN
5
4
1. Axles 2. Drive lines 3. Central gear box 4. Tramming hydraulic motor 5. Bolster
2
1
2
1
3
DRILLING HYDRAULIC COMPONENTS
2 4
3
1
1. Drilling hydraulic oil tank 2. Drilling electric power pack 3. Drilling low pressure oil filter 5
4. Drilling high pressure oil filter 5. Hydraulic oil filling pump
78494380 - 05-06-2007 SR-RB-FL
11 (94)
DD310-26
INTRODUCTION TO MACHINE
REAR SECTION
REAR SECTION
3
1. Diesel power pack 2. Water circuit component
6
3. Electric cable reel 4. Electric box
2
5. Rear stabilizers 6. Air circuit component 7. Manual oil filling pump or electric oil filling pump (optional)
4 5 1
8. Grease pump with hose reel & gun (optional)
8
8 7
12 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
INTRODUCTION TO MACHINE
DIESEL POWER PACK
1 6 3
1. Diesel engine 2. Engine air filter 2
3. Exhaust gas purifier 4. Fuel tank 5. Fuel tank filling cap 6. Tramming pump
8
7. Tramming oil cooler 2
8. Tramming oil tank
7
4
5
78494380 - 05-06-2007 SR-RB-FL
13 (94)
DD310-26
INTRODUCTION TO MACHINE
WATER CIRCUIT COMPONENTS 1b
2
1.a Water supply connection 1.b Water hose reel (optional) 2. Water pump 3. Oil water cooler
3
1a
14 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
INTRODUCTION TO MACHINE
AIR CIRCUIT COMPONENTS
4 1 5
1. Air compressor 2. Rock drill air oiler 3. Air cleaner 4. Air receivers (optional) 5. Mine air supply connection (optional)
6
6. Air mist sight glass (optional) 2
3
2
78494380 - 05-06-2007 SR-RB-FL
15 (94)
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
2.
SAFETY & ENVIRONMENTAL INSTRUCTIONS RISK OF INJURY AND AUTOMATIC VOIDANCE OF SANDVIK WARRANTY TO WHOM IT MAY CONCERN: SANDVIK HAS DESIGNED SAFETY FEATURES BECAUSE IT BELIEVES SUCH FEATURES WILL BETTER PROTECT PEOPLE. DO NOT DO ANYTHING THAT MAY HAMPER SAFETY FEATURES ON EQUIPMENT. It is strictly forbidden to make ANY modification to a Sandvik product without prior written approval of the factory. If ANY modifications are made without written approval, Sandvik can not be held responsible for any accidents, incidents or damage to persons or property, especially if modifications are made on any safety feature including, but not limited to, safety critical circuits or components. In many cases, the affect of a modification to a machine's total performance is unknown.
Therefore, if a machine is modified for any reason, even if safety is not affected, Sandvik's warranty will be void.
2.1.
Operator safety instructions Danger. Operation, maintenance and adjustments are only allowed to persons with specific training in operation and maintenance of the equipment. Read the operating and maintenance instructions before using or servicing the equipment. Danger. Plan your work carefully in advance to avoid possible accidents and injuries. The operator must be familiar with the functions of the equipment before taking it into use. Danger. The operator must always wear required personal protection, such as safety helmet, protective overall, safety boots, hearing protectors, safety goggles etc... Always ensure that those protections are in good shape before using them. Danger. Adequate ventilation must always be provided. Make sure that ventilation is sufficient to prevent exhaust fumes and dust. Exhaust fumes can be lethal. When operating in confined conditions the exhaust gases and dust must be directed in such a way that they do not return to the working area and create a hazard. Check regularly the exhaust purifier clogging according to its maintenance manual. Danger. Always have a fire extinguisher at hand and learn how to use it. Have the extinguisher inspected and serviced regularly according to the local regulations and to the extinguisher maintenance manual.
16 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
Danger. Take care of sufficient lightning. Danger. Insufficient scaling of drilling site. WARNING
2.2.
Main safety hazards in use or maintenance work Danger. MAKE SURE THAT THERE ARE NO UNAUTHORIZED PERSONS IN THE DANGER AREAS DURING DRILLING OR TRAMMING.
WARNING
Danger. Simultaneous charging and drilling is strictly forbidden. Danger. Always check the efficiency of the safety devices before using the machines: emergency stop push button, emergency brakes, backward tramming light and buzzer, tramming and working light, horn, etc... Danger. All hoods must be correctly mounted on the machine and the doors correctly closed and locked, this all the time in order to prevent accident with moving components such a engine belt, cable reel chain, etc... Danger. danger of slipping, tripping or falling. Keep the ladders, steps, hand rails, handles and working platforms clean of oil, dirt and ice. Danger. Observe the balance of the rig. Never exceed the specified inclination angles when parking, tramming or drilling.
Danger. While tramming NEVER SWING THE BOOM, if needed SWING THE DRILL FEED.
Danger. Before moving the booms make sure that the jacks and the stabilizers are firmly in contact to the ground.
Danger. Crushing hazard : do not stay in dangerous area, for instance: central articulation, front chassis and rear chassis..
78494380 - 05-06-2007 SR-RB-FL
17 (94)
SAFETY & ENVIRONMENTAL INSTRUCTIONS
DD310-26
Danger. The movements and rotation of components form also danger areas (boom, feed and drilling equipment). MAKE SURE THAT THERE ARE NO UNAUTHORIZED PERSONS IN THE DANGER AREAS. Danger. Danger of hot surface. Hot surface can cause serious injuries. Components as diesel engine, exhaust gas purifier, rod, shank or hydraulic components can be hot and before starting a maintenance work, please let them cool off. Danger. Service operations should be carried out only when the rig is stopped. Replace or repair faulty tools and equipment. Make sure that there are no unauthorized persons in the working area when you carry out service and repair work. The drilling equipment must always be kept clean of oil and dirt. Danger. Make sure that the boom is properly supported before servicing the hydraulic system.
Danger. Danger of high pressure air streams. The air streams can cause serious personal injuries. Release the pressure before opening filling caps or pneumatic connections. Danger. The lubricator, the compressor air/oil receiver and any air receiver are pressure vessels and they are not allowed to be repaired without proper authorization. Check regularly the certification validity of those componnents. At the end of validity period, you must make recertify the component by a registered organization or replace it by a new one. Danger. Danger of high pressure oil jets. High pressure oil jets can cause serious personal injuries. Release the pressure in the hydraulic circuits before opening caps or connections. (Accumulator,Cylinder and Hydraulic circuit) Danger. If the component must be live, a fellow worker must be standing by to cut OFF voltage at the emergency or main switch in an emergency situation.
WARNING
18 (94)
Danger. If you have to weld the rig, disconnect the alternator cables or open the main switch before starting to weld. Consider also the fire and explosion risk caused by welding. Make sure that the rig and its surroundings are clean and fire-safe.
78494380 - 05-06-2007 SR-RB-FL
DD310-26 2.3.
SAFETY & ENVIRONMENTAL INSTRUCTIONS
Environmental precautions Danger. Please notice that the hydraulic oil, fuel, and battery liquid can cause pollution. Please refer to your own environmental standars for the liquide processing.
WARNING
Before operating maintenance always plan your work in order to use adequate and in good shape receptacles. Do not use the diesel engine if it is not needed because of exhaust gas, think about the people and the environment. For decommissioning, scrapping and disposal of machine’s components (diesel engine, tyres, batteries, etc...), you must always observe the law in force in your country. In case of no law or if you think it’s not suficient, you can contact the conponent supplier. Always have a fire extinguisher at hand and lurn of to use it.
78494380 - 05-06-2007 SR-RB-FL
19 (94)
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
2.4.
Type plate 3 5 1 7
2 4 6
DATE DE FABRICATION
NOM
TYPE
N°SERIE
PUISSANCE INSTALLEE : DIESEL TENSION ALIMENTATION
Kw ELECTRIQUE
Kw
FREQUENCE
Hz
V
POIDS TOTAL DE LA MACHINE
Kgs
SANDVIK MININGAND CONSTRUCTION LYON SAS
6 4 0 1 6 9 0 7
• 1- Machine name and type • 2- Serial number
AV.DE LATTRE DETASSIGNY BP46 69881 MEYZIEU CEDEX FRANCE
• 3- Diesel engine power AV / FRONT PRESSION DE GONFLAGE
AR / REAR
BAR
BAR
TYRE INFLATION PRESSURE
PSI
PSI
• 4- Electric input power • 5- Electric voltage
70961938
9
10
• 6- Electric frequency
11
12
• 7- Total weight of the machine • 8- Manufacturing date
1
2
SANDVIK MININGAND CONSTRUCTION LYON AV.DE LATTRE DE TASSIGNY B.P.46 69881 MEYZIEU CEDEX FRANCE
• 10- Rear tyre inflation pressure (bar)
TYPE N° SERIE
• 9- Front tyre inflation pressure (bar)
N° D’ORDRE
DATE
8
• 11- Front tyre inflation pressure (psi)
13
• 12- Rear tyre inflation pressure (psi) • 13- Order number
2.5.
Gradient angle Danger. The maximum gradient angle is 15°.
WARNING
Danger. The maximum slope angle is 5 °.
side
WARNING
Danger. On slippery surfaces, e.g. ice or smooth rock, safe tramming and drilling gradients are much smaller than on surfaces with good grip. NB: There are two inclination gauges at the tramming compartment.
20 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 2.6.
SAFETY & ENVIRONMENTAL INSTRUCTIONS
Safety telescopic canopy
In order to maintain the safety function and FOPS certification of the canopy, in standing up and sitting down position, the canopy MUST NOT be lowered under the position’s painting red line of the canopy leg.
0 9 2 0 7 7
Red painting line standing up position
5 2
Red painting line sitting down position
5 2
Dimensions in mm
Standing up position Sitting down position
WARNING
Danger. These positions must always be clearly marked on the telescopic canopy leg in order to inform the operator of the machine. You must paint again these red lines on the canopy leg, when the red lines start to be erased. Apply painting red lines over an approximately width of 25mm (1 inch).
78494380 - 05-06-2007 SR-RB-FL
21 (94)
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
2.7.
Machine in tramming position and parking Parking position
B26NV
Tramming position
Parking position
B26F
Tramming position
• Boom and feed extension must be fully retracted. • Boom and feed must be in line with the machine axis. • Lower the drill feed and boom as far as possible. • Machine on stabilizers in parking position.
Danger. While tramming NEVER SWING THE BOOM. - If needed SWING THE DRILL FEED -
22 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
2.8.
Danger areas
2.8.1
Danger area when tramming
5m WARNING
WARNING
WARNING
WARNING
Do not allow other personnel to stand in the area shown beside. DANGEROUS AREAS: • 5m toward the front end of the drill feed and 5m backward the rear end of the carrier. • Area between the machine and the side wall of the drift. Never allow riders on any part of the machine. Always sound the horn before starting the engine.
WARNING
WARNING
The operator must be attentive at any time and have to stop the machine if a person is in the dangerous area. The operator must be also seated with the safety belt fastened, all the time during tramming. Keep hands, arms, legs and head completely inside the tramming compartment. Ensure that the machine is in perfect operating condition. Complete in full, at each shift, the pre-start check list.
5m WARNING
78494380 - 05-06-2007 SR-RB-FL
23 (94)
SAFETY & ENVIRONMENTAL INSTRUCTIONS 2.8.2
DD310-26
Danger area when drilling
NO PERSONNEL ALLOWED
WARNING
WARNING
WARNING
NO PERSONNEL ALLOWED
DURING DRILLING OPERATION, NEVER ALLOW PERSONNEL TO STAND IN THE AREA BETWEEN THE DRILLING COMPARTMENT AND THE ZONE BEING DRILLED. WARNING
A MACHINE SHOULD NEVER BE IN AN AREA THAT HAS NOT BEEN CAREFULLY SCALED.
24 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 2.9.
SAFETY & ENVIRONMENTAL INSTRUCTIONS
Conditions in which the rig should not be used Risk factors for personnel: • Operator does not have sufficient training. • Unauthorized person are present in the working area.
WARNING
• Insufficient scaling of the working area. • Exposition to gases in the drift. • Safety systems are deficient or out of order. • The field is charged. • Transportation of persons. • Use of the rig for lifting purposes. • Inadequate ventilation. • Inadequate lightning. • Inadequate electric earthing. • Defective safety devices.
2.10.
Noise level and noise emission
Noise level The measurement of the noise emission and the noise level at the operator compartment have been measured in accordance of the European Standard Drill Rig safety 89/392/ EEC and changes of 91/368/EEC AND 93/44/EEC. Noise emission:100 db(A) the rockdrill in operation. Level at the operator compartment: 98 db(A) the rockdrill in operation.
2.11.
Acceleration value
The measurement of the acceleration value at the operator’s positions have been measured in accordance of European Standard Drill Rigs - safety 89/392/EEC and changes of 91/368/EEC and 93/44/EEC. Acceleration value does not exceed 0.5 m/s 2
2.12.
Safety equipment Danger. Check the emergency stop buttons and safety equipment for proper operation and condition at the beginning of each shift and always after tramming. • Fire extinguisher(s)
WARNING
• Emergency stop buttons • Safety and protection devices
Danger. Always check the emergency/park brake efficiency prior to move the machine.
78494380 - 05-06-2007 SR-RB-FL
25 (94)
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
2.13.
Fire prevention • Keep the machine clean at all times, especially from fuel, grease, oil rags and paper.
WARNING
• Wash the machine regularly. • Check fire extinguishers and/or fire prevention equipment daily to ensure that they are in perfect working order.When avaible on the unit • Keep electric components and wiring in good condition. • The filling of tanks must be carried out in a well-ventilated area. • The control and recharging of batteries must be carried out in a well-ventilated area.
2.13.1
Refilling fuel
The following precautions must be observed when replenishing fuel: • Do not fill fuel tank when the engine is running. • Take care not to spill fuel on hot surfaces. • Fuel filling should be done in a well ventilated space. • Smoking, open flame and sparks are dangerous when the fuel tank is being filled. • Wipe off spilled fuel before starting the engine. • Keep the fuel replenishing pipe in contact with the fuel tank or arrange earthing to prevent sparking caused by static electricity.
Danger. Smoking during filling or control operations is forbidden.
WARNING
26 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 2.14.
SAFETY & ENVIRONMENTAL INSTRUCTIONS
Fire extinguisher (optional) 2
A PUSH BUTTON
1 PIN
B
Fire extinguisher (optional)
The fire extinguisher actuators are located in A at the tramming compartment and in B at the rear of the machine, as shown on the drawing. To activate the fire extinguisher: • Step 1 : Pull out the lock pin. • Step 2 : Push the red button.
78494380 - 05-06-2007 SR-RB-FL
27 (94)
SAFETY & ENVIRONMENTAL INSTRUCTIONS
2.15.
DD310-26
Emergency stops, main switches and emergency brakes Danger. Always ensure free access to the emergency stops. Danger. Check the operation of the emergency stops prior to use the machine.
WARNING
When any emergency stop push button is depressed, the Diesel engine and the power pack stop at once.
EMERGENCY STOP BUTTONS AT TRAMMING COMPARTMENT AT DRILLING COMPARTMENT
EMERGENCY STOP PUSH BUTTON
EMERGENCY STOP PUSH BUTTON
AT REAR MACHINE
EMERGENCY STOP PUSH BUTTON
28 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
(O) ELECTRIC EMERGENCY/PARK BRAKES OR ABA BRAKES (OPTIONAL) When tramming in emergency situation: • Release the accelerator pedal • Depress the emergency/parking brakes red button. Electric Brakes push button OR ABA Brakes push button (optional)
ABA Brakes caution light (optional) By-passing switch for machine’s towing (optional)
• PUSH TO ACTIVATE THE BRAKES
• Pull to release the brakes • Valve in normal position • If the brake system is released the push button red light turns off • The yellow ABA brakes caution light turns on, if there is a braking circuit pressure falling down:
STOP IMMEDIATLY THE MACHINE AND NOTIFY MAINTENANCE. Danger. Memorize the location of this brake valve in order to be able to activate it rapidly in case of emergency.
WARNING
Danger. The ABA brakes are featured with a safety brake system that applies the brakes automatically when there is a sudden drop in the pressure of the braking circuit. As the machine may come to an abrupt halt, the operator must be correctly seated with the safety belt fastened and attentive at all times. TRANSPORTING PASSENGERS AND STANDING UP WHILE TRAMMING IS STRICTLY FORBIDEN.
78494380 - 05-06-2007 SR-RB-FL
29 (94)
DD310-26
SAFETY & ENVIRONMENTAL INSTRUCTIONS
BATTERY MASTER SWITCH
Caution. So as to prevent the alternator to be damaged, stop the engine prior to turn the battery master switch to the «OFF» position.
OFF
ON
NOTE: In drilling electric mode, switch off the battery in order not to dischange the battery
ELECTRIC MAIN CIRCUIT-BREAKER Danger. Switching off the main circuit-breaker do not ON shut off the power at the OFF cable reel and in the cable connected to the machine. Consequently the cable is still live. NEVER HANDLE A LIVE CABLE. Never leave the machine while motors are running.
ON
RESET
OFF
RESET
Caution. Do not rotate the main switch if a motor is running. Stop all motors prior to use the main switch. NOTE: if the electric main circuit-breaker trip OFF automatically due to an electric problem, move the handle fully to reset position prior to place it back to ON position.
2.16.
Electric cable Danger. Never use an electric cable unless it is firmly positioned on its support. this will prevent unnecessary tension on the cable which may result in the plug being pulled from its socket. The cable must never be live before the machine is ready to drill and the cable itself has been placed in its support and support hooks. NEVER HANDLE A LIVE CABLE. Never move the machine if the cable is live. To ensure that no vehicle will drive over the cable, lay the cable in hooks which have been placed in the sidewall along the length of the gallery being drilled.
30 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
3.
CHECKS AND INSTRUCTIONS
3.1.
Assembly and checking of a new machine
If the machine is delivered disassembled, please pay special attention to the following points: • The assembly site must be properly equipped (cleanliness, good lighting, lifting equipment, etc...). • The assembly operation must be done by qualified personnel. • Check that all components are delivered. • Fasten all bolts and connections properly. • Observe cleanliness when installing hydraulic hoses to prevent particles to enter in the hydraulic circuit. • Lubricate all greasing points. • Wash the machine before using it.
VISUAL CHECKING OF A NEW MACHINE
CENTRAL ARTICULATION LOCKING BAR Check for: • Possible transportation damage. • Tyre pressure and condition. • All oil and fuel levels.
LOCKED BAR IN UNLOCKING POSITION
Locking bar in locking position
Caution. Remove the central articulation locking bar before moving the machine. Danger. All electric safety devices must be thoroughly checked prior to attempt to start the machine. WARNING Danger. The rock drill accumulators must be inflated with NITROGEN (N2).
LOCKED BAR IN LOCKING POSITION
78494380 - 05-06-2007 SR-RB-FL
31 (94)
DD310-26
CHECKS AND INSTRUCTIONS
3.2.
Routine checks before starting a shift Danger. Report any damage or faulty components immediately and do not use the machine.
WARNING
PINS 1
2 TYPE A:
• Lock plate 2 must be in contact to the support 1. • Fastening screws in place and tighten.
1 TYPE B
• Fastening bolt 1 in place and tighten.
TYPE C
• Fastening bolt 1 in place and tighten.
1
HOSES, FITTINGS AND HYDRAULIC CONNECTIONS When moving around the machine, look for hydraulic damages • Hoses • Fittings and connections • Hydraulic leaks
32 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
ENGINE 1
AIR FILTER
• Make sure that the clogging indicator 1 is in the green zone. An indicator located in the red zone calls for filter element replacement.
2
• Expel dust from the pre-filter dust collector 2. • Check the hose between the filter and the engine intake manifold for fraying cracks and damaged clamps.
ENGINE OIL LEVEL
• Ensure that the engine oil is between the minimum and the maximum level marks on the dipstick.
ENGINE OIL LEVEL 78494380 - 05-06-2007 SR-RB-FL
33 (94)
DD310-26
CHECKS AND INSTRUCTIONS
WATER SEPARATOR / FUEL HEATING FILTER (OPTIONAL)
• Open the drain to evacuate contaminants and water. • Close the drain. Drain
WHEELS
3
1
• Visualy check the tyres 1, look for damages. • Make sure the nuts 2 are correctly tighten (Wheel tightenning torque : 400 Nm).
2
• Make sure the lock ring 3 is correctly in place. • Check the tyres’ pressure (10 bar for SOLIDEAL tyres or 8 bar for NOKIA tyres).
CARRIER
Check and grease • Central articulation • Cable guide • Stabilizers • Rear axle bolster
34 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
HYDRAULIC TANKS
TRAMMING HYDRAULIC TANK
1
• Make sure that the hydraulic oil level is above the minimum mark (1) of the sight glass.
DRILLING HYDRAULIC TANK
• Make sure that the hydraulic oil level is above the minimum mark (1) of the sight glass.
1 2A
• If needed fill up the tank to the maximum mark using the hand pump (2A).
OR • If needed fill up the tank to the maximum mark using the electric filling pump (2B). • Push button A to fill drilling hydraulic tank
A
2B
78494380 - 05-06-2007 SR-RB-FL
35 (94)
DD310-26
CHECKS AND INSTRUCTIONS
COMPRESSOR • The clogging indicator (1) should be in the green zone. • A clogging indicator in the red zone, calls for filter element (2) replacement.
2
• Check air inlet components, and inlet hoses for loose clamps and cracks in hose.
1
3 - Air circuit pressure --> must stay between 3 bar and 8 bar (while running)
4 - Compressor oil temperature --> (must stay under 100° c)
WARNING
OIL LEVEL
4
Danger. Do not open the oil filling plug if the receiver is pressurized. Oil is hot when the compressor has just been stopped. Wait 20 minutes before doing any operation on the compressor
3 • First stop the compressor, and make sure that the receiver is pressureless. Blow-out the air circuit after stopping; then wait 15 minutes. • Remove the level dipstick and check the oil level in the compressor. Oil drain
• Remove the oil filling plug and add oil up to the top mark of dipstick. • Screw the filling plug and the dipstick in their place. • Start the air compressor again and stop it after a few time, then repeat the previously described operation to adjust the oil level.
36 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
ROCK DRILL OILER
• Read the gauge 1 and be sure there is no pressure remaining in the air circuit.
1
2
• Open slowly the hand valve 3 to drain the condensed water. • Open the cap 2, This cap includes a dipstick. Pull it up, check the rock drill lubrication oil level. • Once a week, drain all remaining oil, fill up with new rock drill oil.
3
AIR/WATER CLEANER
1
2
- Every shift , bleed the air cleaner 1 and IP5 (optional) 2 • First stop the air compressor. • Open the bleeding valve to remove the condensed water. • Close the bleeding valve before starting the compressor.
78494380 - 05-06-2007 SR-RB-FL
37 (94)
DD310-26
CHECKS AND INSTRUCTIONS
DRILL FEED AND BOOM
TF500 3
3
• Ensure that the rock drill cradle (1) guide shoes are correctly positioned and tightly in place.
1
• Ensure that the feed rails (2) are in good condition and free of dirt which could obstruct the drilling and bolting movements (wash them if necessary). • There must be no missing or loose nuts and screws.
2
• Check condition of pulleys and cable. 3
TTF500 3
1
• Check condition of centralizers (3). • Check all the hoses for fraying or wear.
NOTE: The hoses must be kept under the protection of their spiral sheath.
2
B26 F
• Check and grease all pins and pulleys.
NOTE: Do not grease the rails.
B26 NV
38 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
WATER SUPPLY 1b
Check the water supply 1a Correct water supply connection. OR 1b Correct water hose reel connection. 2 No leaks in water circuit components.
2
The mine water supply pressure must stay between 3 bar and 14 bar. NOTE: A lack of water or a loss of pressure stops all drilling operations (percussion, rotation and feed halted). 2
Caution. If the temperature in the storing place of the machine is lower than the freezing point, the water circuit and the water scrubber must be protected or drained.
1a
WATER PUMP
The water pump must be drained before each start and after each maintenance work on the water circuit. Use the drain ball valve for this operation. NOTE: Read the water pump maintenance manual for this operation if the drain ball valve is not mounted on your machine.
78494380 - 05-06-2007 SR-RB-FL
39 (94)
DD310-26
CHECKS AND INSTRUCTIONS
3.3.
Stardard electric cabinet ELECRIC CABINET
Includes 220 VAC and 24 VDC power supply devices and the control circuits. F251 Fault current circuit breaker for cabin heater and sockets. F291 Fault current circuit breaker for 3 phase socket. F311 Fault current circuit breaker for internal 220V control voltage in main switchgear. F312 Circuit breaker for internal 220V control voltage in main switchgear. F450 Circuit breaker for internal 24V control voltage in main switchgear. F451.1 Circuit breakers for control system and instruments. F452.1 Circuit breakers for working lights. F453.1 Circuit breakers for cabin optional.
GAUGES:
F454.1 Circuit breakers for hydraulic oil filling pump, multi-timer unot and carrier.
P400: Compressor hour meter 1P100: Rock Drill percussion hour meter P410: Supply Voltage meter
F454.5 TMS (optional) F10.1: Circuit breaker for battery charger F10.2: General circuit breaker
FAULT CURRENT TEST 2
1
• Once a month, check the connections condition by doing a current fault test. • To do the test, push the current fault test button 1 at the electric box, the F311 circuit breaker 2 must trip.
40 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 3.4.
CHECKS AND INSTRUCTIONS
Allen bradley electric cabinet ELECTRIC CABINET Includes 220 VAC and 24 VDC power supply devices and the control circuits. F251 Fault current circuit breaker for cabin heater and sockets. (optional) F291 Fault current circuit breaker for 3 phase socket.(optional) F311 Fault current circuit breaker for internal 220V control voltage in main switchgear. F312 Circuit breaker for internal 220V control voltage in main switchgear. F450 Circuit breaker for internal 24V control voltage in main switchgear. F451.1 Circuit breakers for control system and instruments. F452.1 Circuit breakers for working lights.
F452.3 F453.1 Circuit breakers for cabin optional.
F453.4 F454.1 Circuit breakers for hydraulic oil filling pump, multi-timer unot and carrier.
GAUGES:
F454.5 TMS (optional)
P400: Compressor hour meter 1P100: Rock Drill percussion hour meter P410: Supply Voltage meter
F454.6 Circuit breakers for electric cable control. F10.1: Circuit breaker for battery charger F10.2: General circuit breaker
FAULT CURRENT TEST 2 1
• Once a month, check the connections condition by doing a current fault test. • To do the test, push the current fault test button 1 at the electric box, the F311 circuit breaker 2 must trip.
78494380 - 05-06-2007 SR-RB-FL
41 (94)
DD310-26
CHECKS AND INSTRUCTIONS
3.5.
Tramming compartment Tramming control panel
EMERGENCY/PARK BRAKES PUSH BUTTON OR ABA EMERGENCY/PARK BRAKES PUSH BUTTON (optional)
EMERGENCY STOP PUSH BUTTON Stabilizers, canopy and diesel boom supply Cable reel electric control
Fire extinguisher actuator (optional) Engine accelerator pedal Service brake pedal Safety belt
(O) ELECTRIC EMERGENCY/PARK BRAKES OR ABA BRAKES (OPTIONAL) Electric Brakes push button OR ABA Brakes push button (optional)
ABA Brakes caution light (optional) By-passing switch for machine’s towing (optional)
• PUSH TO ACTIVATE THE BRAKES
• Pull to release the brakes • Valve in normal position • If the brake system is released the push button red light turns off • The yellow ABA brakes caution light turns on, if there is a braking circuit pressure falling down:
STOP IMMEDIATLY THE MACHINE AND NOTIFY MAINTENANCE. Danger. Memorize the location of this brake valve in order to be able to activate it rapidly in case of emergency. WARNING
42 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
TRAMMING CONTROLS
3 Main components:
1
4 • 1. Tramming control panel.
5
• 2. Steering wheel. • 3. Emergency stop button. • 4. Stabilizers, canopy diesel boom supply control valve.
2
• 5. Cable reel (and water hose reel: optional) electric control.
TRAMMING CONTROL PANEL • 1. Engine starter. • 2. Horn.
10
12
11
• 3. Tramming Indicator Panel (dash board).
8
• 4. Front/Rear tramming lights.
3
• 5. Forward / reverse tramming direction.
2
• 6. Slow / fast tramming speed selector switch.
5
• 7. Emergency stop button. • 8. Cable reel by pass security.
9
1
7
6
• 9. Tramming pressure gauge.
4
• 10. Emergency electric park brakes or ABA Emergency park brakes push button (optional) • 11. By-passing switch for machine’s towing. (optional) • 12. On / Off high pressure cleaner selector switch.
78494380 - 05-06-2007 SR-RB-FL
43 (94)
DD310-26
CHECKS AND INSTRUCTIONS
CABLE REEL, STABILIZERS, CANOPY & DIESEL BOOM SUPPLY • 1. Front Left jack. • 2. Front Right jack. • 3. Rear Left jack.
4
1
• 4. Rear Right jack
5
2 3
6
7
• 5. Telescopic canopy. • 6. Supplies oil pressure to boom valve (for maintenance use only while diesel engine is running). Push the levers to bring the stabilizers in contact to the ground. Pull the levers to retract the stabilizers in tramming position. NOTE: retract the rear stabilizers first when tramming is needed. Extend the front stabilizers first for parking and drilling.
PUSH
• 7. Cable reel and water hose reel electric control (optional) PULL
Push left the lever to reel electric cable Push right the lever to reel water hose reel Push the lever to reel electric cable and water hose reel. FOOT PEDALS
• Pedal A: Diesel accelerator.
A
• Pedal B: Service brake pedal.
NOTE: To stop the machine or to reduce the speed in a decline, release first the accelerator pedal and, if needed, push the service brake pedal.
B
44 (94)
NOTE: Use pedal A and pedal B with the RIGHT FOOT.
78494380 - 05-06-2007 SR-RB-FL
DD310-26 3.6.
CHECKS AND INSTRUCTIONS
Boom movements B26 F
Divergence
Boom extension
Feed extension
Boom lift
Feed roll over
Feed tilt Boom swing
Feed swing
Feed extension
Divergence
B26 NV Feed tilt
Boom lift
Feed roll over
Feed angle Feed swing
78494380 - 05-06-2007 SR-RB-FL
Boom extension
Boom swing
45 (94)
DD310-26
CHECKS AND INSTRUCTIONS
3.7.
Drilling compartment DRILLING COMPARTMENT
G
I
B
P
G
• B: Boom controls. • D: Drilling controls. • P: Pressure adjustment knobs. • G: Pressure gauges. • S: Switches. • L: Air-oil lubrication sight glass.
W
• W: Warning light: indicates a lack of air or water pressure. • I: Indicator light panel O
S
P Emergency stop
D
• O: Optional lever for boom movement (B26 NV or LC) or rod clamp
BOOM CONTROLS
LEVER 1
• PUSH: Boom down. 5 1
2
4
3
• RIGHT: Right boom swing.
PUSH LEFT
• PULL: Boom up. • LEFT: Left boom swing.
RIGHT PULL
LEVER 2
1
2
3
5
• PULL: Boom retraction. • RIGHT: Right feed roll-over.
PUSH LEFT
4
• PUSH: Boom extension.
RIGHT
• LEFT: Left feed roll-over.
PULL
46 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
LEVER 3
• PUSH: Down feed tilt. 1
2
4
3
5
• PULL: Up feed tilt. • RIGHT: Right feed swing.
PUSH
• LEFT: Left feed swing.
LEFT
RIGHT PULL
LEVER 4
• PUSH: Feed extension. • PULL: Feed retraction backwards. 1
2
4
3
5
PUSH LEFT
• RIGHT: Down feed divergence (boom B26F) or Right feed angle (boom B26NV). • LEFT: Up feed divergence (boom B26F) or Left drill feed angle (boom B26NV).
RIGHT PULL
LEVER 5 (OPTIONAL)
2
3
4
• PUSH: Down feed divergence (boom B26NV).
5
• PULL: Up feed divergence (boom B26NV).
PUSH
PULL
OR • PUSH: Rod clamp closing • PULL the lever: Rod clamp opening
78494380 - 05-06-2007 SR-RB-FL
47 (94)
DD310-26
CHECKS AND INSTRUCTIONS
DRILLING CONTROLS
PUSH
LEVER 1 PULL
• PUSH: Feed return. • PULL: Feed thrust. 1
2
3
LEVER 2
PUSH
• PUSH: Manual percussion (thread and drill bit loosening).
PULL
1
2
3
• PULL: Normal drilling percussion.
PUSH
LEVER 3
• PUSH: Reverse rotation.
PULL
• PULL: Drilling rotation. 1
PUSH
3
LEVER 4
• PUSH: Fast feed return.
PULL
4
5
PUSH
• PULL: Fast feed forward.
LEVER 5
• PUSH: Air flushing
PULL
4
48 (94)
2
5
• PULL: Water flushing
78494380 - 05-06-2007 SR-RB-FL
DD310-26
CHECKS AND INSTRUCTIONS
ADJUSTMENT KNOBS STANDARD DRILLING CONTROL
B • A: Feed pressure control knob. Turn clockwise to increase pressure, counter clockwise to decrease pressure.
A DRILLING CONTROL WITH OPTION
• B: Rotation speed control knob. Turn clockwise to increase RPM, counter clockwise to decrease RPM.
A B
PRESSURE GAUGES A B
C D E
• A: Air pressure gauge. • B: Water pressure Gauge • C: Rotation pressure gauge. • D: Percussion pressure gauge. • E: Feed pressure gauge.
AIR MIST (OPTIONAL)
A B
78494380 - 05-06-2007 SR-RB-FL
• A: Air mist sight glass • B: Turn flow controler to ajust water flow
49 (94)
DD310-26
CHECKS AND INSTRUCTIONS
SWITCHES & JOYSTICK
E
• A: Power pack on/off - Ensure that all the control levers for the hydraulic control valves, particularly the drilling control levers, are in the Neutral Position - Turn switch A in position 2,the power pack starts.Then the switch automatically return to position 1.Turn to left (position 0) power pack stops
F G
01 2 10 2 A
B
10 2
10 2
C
D
• B: Automatic feed return control. - Switch to the left (1):Manual feed return using control levers, all 3 drilling levers free. - Switch in central position (0): Automatic feed return at the end of drilling operation, all 3 drilling joystick levers hold in full drilling position - Switch in central position (2):While drilling if there is an need for stopping the drilling process, it moves the rockdrill backward immediatly and resets the 3 drilling levers to neutral. From this position the switch return position 0 when is not maintained.
EMERGENCY STOP • E: Joystick TRS (Optional)
Right: Swing up TRS Left: Swing down TRS Push: Close TRS Pull: Open TRS • F: Joystick Rod Clamp TRR1 (Optional)
Right: Open rod clamp Left : Close rod clamp • G: Automatic central greasing (Optional)
Additional lubrication cycles can de triggered at any time.
• C: Compressor - Switch in central position (0) auto start with power pack - Switch to the right (2) power pack starts. - Switch to the left (1) power pack stops. • D: Water Pump on/off - Switch in central position (0) auto start with power pack - Switch to the right (2) power pack starts. - Switch to the left (1) power pack stops.
SIGHT GLASS The rock drill shank is lubricated with oil mixed in pressurized air. Air-oil drill lubrication sight glass
• While drilling, air/oil mix must flow through the sight glass. If the glass seems dry, stop drilling operation and check the oiler (see page 37). NOTE: A loss of air pressure stops all drilling operations (percussion, rotation and feed halted).
50 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 4.
TRAMMING
4.1.
Starting the engine
TRAMMING
Danger. Always make sure before starting the engine that there is no unauthorized persons in the danger areas around the machine and that no controls are in operating position. The operator must fasten his seat belt before starting the engine . WARNING
Danger. Sound the horn to warn any person of your intention to start and move the machine. Make sure that all covers and protective hoods and doors are installed and properly closed ELECTRIC SWITCHES • Turn the batteries master switch to the ON position (See: paragraph 2.15. page 28). • Make sure the tramming direction switch 2 is in the center in neutral position and rotate the speed selector 6 to the left in low speed position (turtle).
(O)
4 6 2 3
• Turn the tramming light switches 3 to the right • Ensure that the brake is applied. The push button (O) must be ignite red. • Sound the horn 4 to inform everybody of your intention to start the engine. • Turn key 1 to start diesel engine
Caution. Do not run the starter longer than 10 seconds at a time. Wait the starter to cool down before new starting attempt (10 seconds).
1
Electric cable in the cable feed chut.
Caution. .After operating,if you switch off the mine electric supply and still use machine’s lights without have rotated the key 1 to the left in order to start and use the diesel engine, you will unload the battery.
WARNING
78494380 - 05-06-2007 SR-RB-FL
Danger. During the tramming, the electric cable must be in cable feed chut in order to prevent cable damage. 51 (94)
DD310-26
TRAMMING
ELECTRIC PANEL
Display
1
Upper default display is fuel level, when carrier key switch S2 is turned on. Upper default display become diesel RPM reading when diesel is running Lower default is diesel hours, when carrier key switch S2 is turned on
Upper Buttons
2 3
5
4
2. Engine coolant temperature. The temperature should be under under 100 C. Indicator light and display blinks and buzzer is on if temperature is over113 C. 3. Fuel level. The indicator light and display blinks if level is too low. 4. Engine oil pressure. Normal pressure is over 1 bar. Indicator light and display blinks and buzzler is on if pressure is below 0,7 bar.
When you push top line button you have on upper display that reading .When you push top line button over 2 seconds there is again diesel RPM reading. Alarm came always on top and also button indicator light is then on.
Lower Buttons When you push lower line button you have on lower display that reading. alarm came always on top and also button indicator light is then on.
All Button All button indicator light have indicator light test.
when carrier key switch s2 is turned on all button indicator light flash.
5. Voltmeter. The indicator light and display blinks and buzzer is on if voltage is under 20VDC.
52 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TRAMMING
WARNING LIGHTS
1. Blinker (option) Indicator light blink if left or right blinker is on.
2. Service Brake. This indicator light is on if front or rear brake pressure is below 100 Bar.
3. Park brake Indicator light is on if brake pressure is below 5 bar. 4. Pre-heating indicator. The engine can be started when the indicator light up.If the engine is already warm, preheating is not necessary. 5. Charging. The indicator lights up if the alternator is not operational. Switch off the engine and look for the cause.
1
6
2
7
3
8
4
9
5
10
6. Hydraulic transmission Charge pressure.Indicator light is lit the pressure drop under 15 bar.
7. Fuel filter Water in fuel indicator (optional).
8. Transmission oil tank level. Indicator light is on if oil tank level is too low. 9. Air filter indicator light is on if filter is clogged (optional).
10. Low engine coolant level. Indicator light is on if coolant level is too low.
78494380 - 05-06-2007 SR-RB-FL
53 (94)
DD310-26
TRAMMING
TRAMMING CHARGE PRESSURE GAUGE
• Let the engine in idle position and check the tramming charge pressure gauge 1, it must show a minimum of 12 bar.
1
4.2.
Emergency/parking brake test BRAKE TEST • Raise the machine on stabilizers, no contact between tyres and ground.
1
2
3 4
• Install a 600 bar gauge at the tramming test point (1) to verify there is no problem on the tramming circuit (Caution, high pressure). • Apply the parking brake by depressing the emergency button (2). • Select one tramming direction and accelerate slowly => The tramming pressure must increase to 400 bar and no wheel must turn.
Danger. USE ONLY 0-600 bar GAUGE DUE TO THE HIGH PRESSURE. WARNING
Danger. if the wheels turn, do not use the machine and inform a responsible person immediately. WARNING
SERVICE BRAKE TEST : • Raise the machine on stabilizers, no contact between tyres and ground. • Select one tramming direction and accelerate to put the wheels in rotation. Release the accelerating pedal (3) and push on the braking pedal (4). • => Wheel must rapidly stop turning.
In case that the brakes are faulty, do not use the machine and refit it. 54 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 4.3.
TRAMMING
Electric cable CABLE REEL CONTROL CABLE REEL CONTROL
• Position the cable reel control lever in the neutral position N. • Ensure that the power supply from the mine electric box to the machine is OFF. • Plug the cable into the mine electric box. • Secure the cable on the support provided by the mine.
A N
• Tram to the face to be drilled.
• Push button (1) to reel the cable • Push button (2) to unreel the cable
1
2
EMERGENCY STOP
Danger. During the cable unreeling, check the cable tension so that the cable is tight and doesn't stick itself inside the carrier, in order to prevent cable damage.
Danger. Never use an electric cable unless it is firmly positioned on its support. this will prevent unnecessary tension on the cable which may result in the plug being pulled from its socket. The cable must never be live before the machine is ready to drill and the cable itself has been placed in its support and support hooks. NEVER HANDLE A LIVE CABLE. Never move the machine if the cable is live. To ensure that no vehicle will drive over the cable, lay the cable in hooks which have been placed in the sidewall along the length of the gallery being drilled.
78494380 - 05-06-2007 SR-RB-FL
55 (94)
DD310-26
TRAMMING
4.4.
Moving the machine FORWARD / BACKWARD 2
• Always refer to the maximum gradient angle (See: paragraph 2.5. page 20).
A
• Make sure the boom is in tramming position(See: paragraph 2.7. page 22). • Retract the stabilizers (rear first then front). • Pull up the brake valve to release the brakes • Select the direction you want by turning the switch 2 to the left to move forward, to the right to move backward. • Press or Depress on the accelerator pedal A. The speed depends on the Diesel engine RPM.
Danger. sound the horn to warn people before moving the machine. WARNING
WHERE USING LOW SPEED RANGE?
1
• Turn the tramming speed selector 1 to the right in low speed range (turtle symbol) in incline, decline, in busy or crowded areas and in working areas. • Drive slowly around corners, sound the horn and warn people in areas you cannot see. • Observe mine speed limit regulation.
HOW TO STOP THE MACHINE?
B
In normal tramming conditions to stop the machine you must: • Release the accelerator pedal the machine (will reduce speed). • Slowly push with the right foot on the service brake pedal B.
56 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TRAMMING
EMERGENCY STOPPING
(O) In case of emergency, push the red button (O) to activate the emergency brake.
4.5.
Parking the machine
To park the machine safely, select an area clear of personnel and a location where the machine will not obstruct passage of other equipment. • Bring the machine to a full stop. Release the accelerator pedal and press on tramming control pedal. • Apply the emergency/parking brakes. • Position the two (2) rear stabilizing jacks and the two (2) front jacks firmly on the ground. The distance between the wheels and the ground must not be more than 7 mm (1/2"). • The machine must be turned into a bank or rib to prevent it from running away. Place a stop block on the wheels when parking a gradient. • Allow the diesel engine to idle several minutes to allow critical components to cool gradually. • Stop the engine by pressing the "OFF" button. • Turn the battery master switch to the "OFF" position.
Danger. NEVER LEAVE THE MACHINE WHILE THE ENGINE IS RUNNING.
WARNING
78494380 - 05-06-2007 SR-RB-FL
57 (94)
DD310-26
DRILLING
5.
DRILLING
5.1.
Setting-up the machine in the drift
Place the machine lengthways of the drift at an equal distance from the sidewalls.
For optimum stability, and perfectly parallel holes, the chassis must be on line with the gallery being drilled. Stop the machine so that the distance between the machine and the face to be drilled = the length of the drill feed + 300 mm (1 foot). This position will allow the drill feed to access the lifters which are directly aligned with the machine.
Drill feed overall length Position of the lifter
58 (94)
2’ Mini. clearance Front of the chassis
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
Place the stabilizers firmly on the ground, do not over lift the chassis for optimum stability. Danger. When placing the stabilizers, pay attention that nobody is close to them.
WARNING
Optimum stability
78494380 - 05-06-2007 SR-RB-FL
59 (94)
DD310-26
DRILLING
5.2.
Electric power
Check following points before switching the mine circuit-breaker ON. • Machine correctly installed • Water hose connected • Air hose connected (optional) • Electric cable carefully positioned along the sidewall
MACHINE CIRCUIT BREAKER
ON
OFF
ON
NOTE: To be able to use the machine circuitbreaker you should turn first the battery master switch ON (See: paragraph 2.15. page 28). Rotate then the main circuit-breaker in position ON.
RESET
OFF
RESET
After using of the emergency stop button the main circuit breaker will be placed automatically in TRIP position. To reset the power to the machine - Rotate the lever fully to RESET position. - Then rotate clockwise in ON position. NOTE: Do not use the emergency stop button in normal process to stop any of the power pack, use dedicated stop button.
60 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
INDICATOR LIGHT PANEL
H608
Overload of powerpack motor for boom 1 and 2. The indicator light goes on if the motor’s protective switch (F100) is triggered or, if the thermal protector alarms (motor temperature over 155 C). The protective switch must be reset by turning its control switch first to 0 position and then to 1 position. The thermistor protector is reset automatically as the motor temperature drops. The indicator light goes on also if the magnetic triggering of the protective switch comes activated when the powerpack is started.
Powerpack of boom 1 and 2 running.
Compressor running.
Water booster pump running.
High–pressure water pump running (Optional).
78494380 - 05-06-2007 SR-RB-FL
61 (94)
DD310-26
DRILLING
H608
Low water pressure. If the water pressure stays below 2.8 bar for longer than 4 seconds (default setting), the pressure monitoring system stops drilling and stops the water pump. The indicator light remains lit and it can be turned off by pressing the bypass/acknowledgement button S505. After that,water pump has to be started manually with switch S501. Compressed air too hot. If the temperature of the output air from the compressor rises too high, the powerpack, the compressor, and the water pumps stop and the indicator light goes on. The indicator light goes off automaticallyas the compressor cools down. Compressor motor overloaded. The indicator light goes on and the powerpack,the compressor and the water pumps stop when the compressor’s protective switch F240 is triggered. The protective switch must be reset manually. Turn the main switch to the 0 position before resetting the protective switch. Water booster pump motor overloaded. The indicator light goes on and the powerpack, the compressor and the water pumps stop when the water pump’s protective switch F230 is triggered. The protective switch must be reset manually. Turn the main switch to the 0 position before resetting theprotective switch.
H609
Low air pressure. If air pressure stays below 2.8 bar for longer than 10 seconds (default setting), the pressure monitoring system stops drilling. The indicatorlight remains lit and it can be turned off by pressing the reset/ acknowledgementbutton S505. High–pressure water pump motor overloaded. The indicator light goes on and the powerpack, the compressor, and the water pumps stop when thehigh–pressure water pump’s protective switch F280 is triggered. The protectiveswitch must be reset manually (Optional equipment).
62 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
H608
Low oil level of hydraulic oil receiver or shank lubrication device. If the oil level drops below the allowed minimum, the powerpack, the compressor and the water pump stop and indicator light goes on. The level monitoring system has a 3–second time delay for preventing false alarms if the oil level momentarily drops too low, for instance, when the rig rocks. rocks. The indicator light goes off when a sufficient amount of oil is added.If the indicator light blinks, the oil level in the shank lubrication is low.
Return filter clogged. When the indicator light goes on, the one of return filter has come so dirty that it must be replaced. The filter monitoring device does not stop drilling functions. When the oil is cold (below 30 C), the monitoring system is bypassed to avoid alarms caused by thick oil. Hydraulic oil too hot. If the temperature of the hydraulic oil rises over 75 C the powerpack, the compressor and the water pumps stop and the indicator light goes on. The indicator light goes off automatically when the oil temperature has dropped sufficiently. Clogged pressure filter of powerpack for boom 1 and 2. When the indicator indi cator light goes on, the pressure filter has come so dirty that it must be replaced. The filter monitoring device does not stop drilling functions. When the oil is cold (below 30 C), the monitoring system is bypassed to avoid alarms caused by thick oil. Emergency–stopped. Emergency–stopped. When any of the emergency stop buttons of the rig is depressed the indicator light goes on, all motors stop and diesel stops. By releasing the button(s), the indicator light can be turned off, but the motors must be restarted separately.
78494380 - 05-06-2007 SR-RB-FL
63 (94)
DD310-26
DRILLING
H608
Incorrect phase sequence. When the main switch is turned ON, the relayK120 checks the 3–phase current for correct direction of rotation. If the directionof rotation, i.e. the phase sequence, is incorrect, the indicator light goes on and the motors are prevented from from starting. Overload of air–conditioning compressor motor. The indicator light goes on and the compressor stops when the protector switch F260 is triggered. The switch must be reset manually (Optional equipment). Electric current switched ON. The indicator light goes on when the main switch is turned ON.
Electric motor of air–conditioning compressor running (Optional).
External pump running (Optional).
Earth fault current (Optional).
External pump overflow. overflow. The indicator light goes on and the powerpack, the compressor and the water pumps stop when the protector switch switch F290 is triggered. The switch must be reset manually (Optional).
64 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
HYDRAULIC POWER PACK START UP • Ensure that all the control levers for the hydraulic control valves, particularly the drilling control levers, are in the NEUTRAL POSITION.
01 2
A
78494380 - 05-06-2007 SR-RB-FL
• Turn the switch A to the right (1) power pack is under tension, turn to the right (2) power pack starts and automatically return to position 1. Turn to the left (0) power pack stops.
Caution. Wait several seconds before using any one of the control lever.
65 (94)
DD310-26
DRILLING
5.3.
Parallelism setting INITIAL POSITION SETTING
• The front frame of the machine should be levelled and in the axis of drilling direction.
Boom position: • Use the boom lift lever to bring the boom in horizontal position. • Use the boom swing lever to line up the boom with the front carrier axis.
Drill feed position: • Use the roll-over lever to bring the drill feed suppor t cradle to the position shown below. • Use the feed swing and the drill feed tilt lever to line up the roll over axis with the front carrier axis. • Use the divergency lever to bring the drill feed to the horizontal position
NOTE: The boom is now set. If the last 3 movements are not used, the drill feed will remain in the parallel drilling mode. NOTE: For overall improved rigidity of the boom, it is recommended to use the boom extension when approaching the drill feed to the face instead of the feed extension cylinder.
66 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
HOW TO REDUCE THE DEAD ANGLE? BOOM EXTENSION RETRACTED - DRILL FEED EXTENDED
F 6 2 B
Stinger
BOOM EXTENSION EXTENDED - DRILL FEED RETRACTED
BOOM EXTENSION EXTENDED - DRILL FEED RETRACTED
BOOM EXTENSION RETRACTED - DRILL FEED EXTENDED BOOM EXTENSION RETRACTED - DRILLFEED EXTENDED
V N 6 2 B
BOOM EXTENSION EXTENDED - DRILL FEED RETRACTED BOOM EXTENSION EXTENDED - DRILL FEED RETRACTED
A dead angle zone, when the rear section of the drill feed interferes with the boom, can occur when drilling the blast hole (burn cut). • Extend the feed extension movement cylinder to near maximum capacity. • Position the drill feed near the zone to be drilled, by using the boom extension, swing and lift movements. • Anchor the stinger with the remaining feed extension travel.
NOTE: it is the only position where drilling is recommended using the feed extension fully extended.
78494380 - 05-06-2007 SR-RB-FL
67 (94)
DD310-26
DRILLING
5.4.
Setting drill feed TTF and TFX
1. Open the ball valves (1) and (2) fully. 2. Feed the rock drill forward until the whole system is as short as possible (refer to Figure 2 ‘Maximum and minimum length’). 3. Close the ball valve (2) fully. 4. Feed the rock drill backward until it is facing the rear stopper. 5. Run the rock drill backward against the rear stopper for about 10 seconds. 6. Close the ball valve (1) fully. 7. Check that both ball valves (1) and (2) are fully closed. (Also see the shield on the next page).
68 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
Setting TFX 500 to different lengths by using an instruction as a reminder. For setting the length to minimum, follow the steps (1 to 5) which are described on the plate’s upper picture. For setting the length to intermediate or maximum, follow all the steps (1 to 11) which are described on the plate. The steps are read from left to right and top to bottom. STEPS: 1. Open the ball valves (1) and (2) 2. Feed the rock drill forward until the whole system has the shortest position. 3. Close the ball valve (2) fully. 4. Feed the rock drill until it is facing the rear stopper for approximately 10 seconds. 5. Close the ball valves (1) and (2) 6. Open the ball valves (1) and (2). 7. Run the feed’s inner tube into desired length by running the rock drill against the rear stopper. 8. Close the ball valve (2). 9. Feed the rock drill against the rear stopper for approximately 10 seconds. 10. Close the ball valve (1) fully. 11. Open the ball valve (2) fully.
78494380 - 05-06-2007 SR-RB-FL
20960108
69 (94)
DD310-26
DRILLING
5.5.
Collaring a hole DRILL FEED POSITIONING
• Using lever 1 and 2 move the drill feed in the position you need to drill a hole. • Push the lever 4 to bring the drill feed stinger in firm contact with the rock. 2
1
3
4
• Pull percussion lever 2 fully • For smooth collaring pull slowly rotation lever 3 and feed lever 1. Keep the levers 3 and 1 in the position where the movements have started. • Let the bit penetrated the face until it reaches solid rock.
PUSH
4
1
5
2
3 PULL
5.6.
When the bit has reached solid rock, collaring process is achieved. Full drilling power can be used.
Normal drilling DRILLING OPERATION
• Pull levers 1, 2, 3 fully. PUSH
4
5
1
2
3 PULL
1
0
B
2
NOTE: All levers will be maintained in full power position during all drilling process. If the switch B is placed in center position (0) the percussion will stop automatically at the end of the feed travel and the feed movement will be reverse in backward direction. The reverse motion will stop automatically when the rock drill reaches the end of the drill feed rear point. Turn the switch B to the right position (2) to stop the drilling process. All drilling levers 1, 2 and 3 will move back to neutral, NOTE: Use the emergency stop button only in case of emergency. In normal process use dedicated button to stop any operation.
70 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
DRILLING
DRILLING ADJUSTMENT While drilling the operator can adjust the rotation speed (RPM) as well as the feed pressure. NOTE: Always adjust both rotation and feed at the best level acceptable according to your ground condition. Rotation over-speed will result in a faster wear of the bit carbide inserts, mainly in abrasive rock. Under-feeding will result in rapid wear of the rod, shank and coupling threads. A smoking coupling indicates under feeding, increase the feed pressure when the coupling smokes.
B
A
Over-feeding will result in an increase in the rotation pressure which indicates an over-torque. That reduces the life time of the rotation mechanism of the rock drill. While drilling keep the rotation pressure to an average value of 50 bar. • A: Feed pressure control knob. Turn clockwise to increase pressure, counter clockwise to decrease pressure. • B: Rotation speed control knob. Turn clockwise to increase RPM, counter clockwise to decrease RPM.
DRILLING IMPERATIVES
CLEARANCE ANGLE
The following rules guarantee optimum drilling performance, resulting in high productivity at low operating costs. The bit: A correct clearance angle and proper water pressure, evacuate the cutting as soon as they have been broken from the face. Drilling with a worn bit results in an increase in rotation torque and loss of penetration rate. To increase productivity a worn bit should be replaced with a new or re-sharpened one. Drill steel and shank adaptor These tools are essential to productive drilling. They transmit percussion and rotation energy to the bit if kept correctly on line. Correct alignment allows optimal energy transmission, reduced wear of the drill steel against the guide shoes, perfect hole alignment, minimum drill steel torsion, and prevents premature breaking of the shanks and drill steels. NOTE: Often control the guiding elements, the shank and the flushing head and report immediately noticed anomalies on every parts of the drill feed and rock drill.
78494380 - 05-06-2007 SR-RB-FL
71 (94)
TRANSPORTATION
5.7.
DD310-26
Rod uncoupling
Recommended procedure for uncoupling the bit or the shank adaptor. • Anchor the drill feed and then open the water circuit. • DO NOT USE THE ROTATION. • Using the Feed Lever , advance the rockdrill. • Move the Feed Lever to the "MAXIMUM feed" position. This allows the full percussion energy to be activated for a better breaking capability.
5.8.
Ending a shift
When you stop the drilling process at the end of the shift or for any other reason, carry on following operations: • Tilt the front end of the drill feed downward, the stinger in contact to the ground. • Stop all powerpack. • Close the water supply valve at the mine line. • As to prevent the alternator to be damaged, stop the diesel engine prior to turn the battery master switch to the "OFF" position. • Place the main circuit breaker to the "OFF" position. • Shut OFF the power at the mine electric box. • Wash the machine mainly the drill feed and the boom. • Fill-up the shift report form. • Report any defects that you have noticed.
6.
TRANSPORTATION
6.1.
Transportation on a platform Danger. Before driving the machine onto a transport platform, move the boom and the feed to the tramming position. never exceed the maximum side and slope limitation. While moving the machine NEVER SWING THE BOOM.
WARNING
When driving the machine onto a transport platform, use ramps. this should always be done on level ground. Always use low speed and observe special caution when coming from the ramps to the platform.
WARNING
72 (94)
Danger. Install the locking bar at the central articulation before moving the platform. Lower all stabilizers against the platform floor. Move the boom as low as possible and fasten it to platform. Fasten the machine chassis to the platform using proper straps or chains.
78494380 - 05-06-2007 SR-RB-FL
DD310-26 6.2.
TRANSPORTATION
Towing the machine Danger. THE MAXIMUM TOWING SPEED MUST BE 1 KM/H. This to prevent the tramming components to be damaged. THE USE OF CABLE OR CHAIN IS STRICTLY FORBIDEN. While towing, one operator should be at the tramming compartment ready to apply the brake in a case of emergency or operate the steering valve to allow the steering cylinder to move.
If it is necessary to tow the machine, comply to the following procedure: • Ensure that the power supply from the mine electric box to the machine is OFF. • Unplug the cable into the mine electric box. • Connect up the towing machine to the towed machine with a RIGID BAR. Hook the bar at the towing points located at the rear of the machine (see the figure below).
Towing point RIGID TOWING BAR 0 1
ABA brakes by-passing switch Optional unbraking hand pump at tramming compartment
Caution. Never try to tow the machine if the multi-function HP valves, located on the tramming pump (see figures below) are tightened. The maximum towing distance allowed is 1/2 km, over this distance the hydraulic motor(s) could be damaged due to lack in internal lubrication.
78494380 - 05-06-2007 SR-RB-FL
73 (94)
DD310-26
TRANSPORTATION
• For a machine with optional ABA brakes, turn the ABA brakes by-passing switch in position 1, in order to by-pass the ABA brakes safety device. • Untight the both valves and turn them four revolutions counter-clockwise, to by-pass the oil flow. The tramming motor can now turn without resistance. Unscrew Multi-function HP valves Unscrew
Valve in towing position • Release the emergency/park brake valve by pulling, fully upward, the red knob. • Close the ball valve of the unbraking hand-pump.
Danger. This ball valve must be always open in normal use of the machine. If not, the park brake may not work, don’t forget to reopen the ball valve after towing the machine.
• Use the unbraking hand pump to pressurize the brake cylinders. The pressure build up by the hand pump is sufficient to release the brakes.
NOTE: The brake valve is always functionning. To apply the brakes push downward the red knob, as you do in normal conditions. Danger. Never try to tow a machine which presents problems on tramming components
Danger. The valves should be retighten as soon as the towing process as been completed. NEVER START THE ENGINE THE HP VALVES IN UNTIGHTEN TOWING POSITION.
74 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 6.3.
TRANSPORTATION
Lifting the machine
LIFTING POINT
LIFTING POINT LIFTING FRAME
LOCKED BAR IN LOCKING POSITION
Danger. Always respect the law and all the local safety regulations in lifting work. Keep in mind the total weight of the rig, given in the technical data pages at the end of this manual. Move the boom and the drill feed to the tramming position (See: paragraph 2.7. page 22). Install the locking bar at the central articulation. Install 4 hooks and chains or cables at the front and rear lifting points. Danger. Do not stand under the machine during lifting process. Use proper lifting devices as hooks, cables or chains for a safe work. Use a lifting frame to maintain all 4 four chains or cables perfectly vertical and parallel each other.
78494380 - 05-06-2007 SR-RB-FL
75 (94)
TRANSPORTATION
DD310-26
The lifting device used must be of the correct type and have sufficient lifting capacity. The rig or parts of it must not be lifted with any devices that are not specifically designed for lifting purposes. You must always know the exact weight of the load, and never exceed the lifting capacity specified by the manufacturer of the lifting device. Lifting routes should be planned so that the load is not moved over persons or such places where persons may be present. Make sure that the lifting equipment is in proper condition Wire ropes and chains used for lifting must be checked regularly. Damaged wire ropes must be marked clearly and discarded at once. Lift the load only a few centimetres at first to make sure that it is properly fastened and in balance. Do not continue lifting until you are sure of proper fastening and balance. The lifting wire ropes must be fastened according to the manufacturer’s instructions.
6.4.
Storing the machine
• The storing place temperature should be higher than the freezing point, and protected against direct sunlight and rain.
Caution. If the temperature in the storing place of the machine is lower than the freezing point, the water circuit, all the water components and the water scrubber must be protected or drained.
• Wash the machine if it has been used or transported by sea using a high pressure steam washing machine. • Drain and blow air through the water circuit. Blow some anti-freeze (rust inhibitor) through the circuit. • Lubricate all greasing points. • Bring the stabilizers in contact to the ground. • The drill feed stinger should be in contact to the ground. • The nitrogen rockdrill accumulator should be empty, PLACE A TAG TO REMIND THAT THE ACCUMULATORS HAVE BEEN DISCHARGED. • Coat the cylinder rod with grease. • Drain the air reservoir(s). • Replace all fluids: engine, hydraulic axle and gear oil. • Spray a dust and corrosion inhibitor product on all electric devices. • As to prevent the alternator to be damaged, stop the engine prior to turn the batter y master switch to the "OFF" position.
76 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 7.
TECHNICAL DATA
TECHNICAL DATA
Technical Specification 6-232 S-E 2007-06-01
Sandvik DD310-26
APPLICATION
MAIN SPECIFICATIONS
Sandvik DD310-26 is a single boom electro hydraulic jumbo for mine development and tunneling in cross sections up to 38 m².
Carrier Safety canopy Rock drill Feed Boom Control system Powerpack Shank lubrication device Air compressor Water pump Main switch Cable reel Length Width Height Weight (without options) Tramming speed - Horizontal - 14% = 1:7 = 8° Gradeability, max Noise level
The robust universal boom have a large optimum shaped coverage, 360° rotation and full automatic parallelism for fast and easy face drilling. The boom can also be used for cross-cutting and bolt-hole drilling. The jumbo layout is designed for good visibility and balance, this and the powerful four-wheel-drive articulated carrier ensure fast and safe manoeuvering in narrow drifts. The high performance drilling system allows high drilling performance with good drill steel economy and high machine reliability. The operator environment and added automatic functions allow the operator to concentrate on safe, fast and accurate drilling. All the service points are well protected but easy to access.
78494380 - 05-06-2007 SR-RB-FL
1 x TC 5 1 x FOPS / ROPS 1 x HLX5 1 x TF 500 1 x B 26 F 1 x THC 560 1 x HP 560 (55 kW) 1 x KVL 10-1 1 x CT 10 1 x WBP 1 1 x MSE 05 1 x TCR 1 10 855 mm 1 750 mm 2 100 / 3 100mm 12 000 kg 12 km/h 5 km/h 35 % < 98 dB(A)
77 (94)
DD310-26
TECHNICAL DATA
Technical Specification 6-232 S-E 2007-06-01
Sandvik DD310-26
GENERAL DIMENSIONS
3100
1980 1675
1600
160 1500
1500
2510
Overall Length
TF 500 x 10 TF 500 x 12 TF 500 x 14 TF 500 x 16
6350
10 855 11 180 11 195 12 250 All dimensions in mm
HLX5 ROCK DRILL
B 26 F BOOM
Weight Length Profile height Power class Max working pressure
Type Weight (with hoses) Feed roll-over Boom extension Feed extension
210 kg 955 mm 87 mm 20 kW - Percussion 225 bar - Rotation 175 bar Max torque (80 ccm motor) 400 Nm Hole size 43 - 64 mm Recommended steel T38- H35-R32 T38-H35-alpha 330 T38-R39-R35 Shank adapter 7304-7585-01 (T38) Flushing water pressure 10 - 20 bar
TF 500
Cylinder - wire rope 25 kN 500x10 500x12 500x14 500x16
Total length (mm)
4660
5270
5880
6490
Drill steel length (mm)
3090
3700
4305
4915
Hole depth (mm)
2830
3440
4050
4660
Net weight (kg)
470
500
530
560
78 (94)
Parallel holdin 1 900 k 360 1 200 m 1 600 m
THC 560 CONTROL SYSTEM Power control Rotation control Automatic functions
TF 500 FEED Feed type Feed force
(Technical specification 4-200
Boom controls
Adjustable full powe Adjustable collaring powe Adjustable rotation spee Reversible rotatio Collarin Feed controlled percussio Anti-jammin Flushin Stop-and-retur Fully proportiona
HP 560 POWER PACK Electrical motor
1 x 55 kW (75 hp 3-phase moto
Pump types - Percussion, feed & boom Axial piston 1 x 130 l/min variable displacemen - Rotation 1 x 60 l/min gear pum Filtration - Pressure 1 x 20 micro - Return 1 x 10 micro Hydraulic tank volume 180 liter
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
Technical Specification 6-232 S-E 2007-06-01
Sandvik DD310-26
TRAMMING DIMENSIONS
2100 Overall Length
TF 500 x 10 TF 500 x 12 TF 500 x 14 TF 500 x 16
10 855 11 180 11 195 12 250
320
15°
3000
2510 6350
TURNING RADIUS
CS R2 R1 40° 5550
TF 500 x 10 TF 500 x 12 TF 500 x 14 TF 500 x 16
R1 3260 3260 3260 3260
R2 5655 5800 5945 6070
CS 3290 3435 3580 3705
All dimensions in mm
TC 5 CARRIER
WATER CIRCUIT
Diesel engine Deutz BF4L 2011, 55 kW (74hp) - Exhaust Catalyser Transmission Hydrostatic, automotive Transfer case Drop gear Clark-Hurth Axles, Front & Rear Case New Holland D45 - Oscillation Rear axle, 2 x 10° - Tyres 12.00 x 20 Steering Frame steering, 2 x 40° Brakes - Service Hydrostatic transmission+positive braking - Emergency & parking Hydraulic oil immersed multiple disc brakes on both axles Stabilizers 2 hydraulic jacks, front 2 hydraulic jacks, rear Safety canopy Hydraulic, FOPS-ROPS - Lowering capability 1 000 mm Fuel tank 80 liters Hydraulic tank 55 liters
Water pump type 1 x WBP - Capacity 30 l/min at 11 ba - Electric motor 4 kW (5.5 hp Oil cooler OW 30, water-actuated counterflo - Cooling capacity 30 k
AIR CIRCUIT Compressor - Capacity Electric motor Shank lubrication device - Air consumption - Oil consumption
78494380 - 05-06-2007 SR-RB-FL
C.T. 10, screw type 1000 l/min at 7 bar 7.5 kW (10 hp) 1 x KVL 10-1 250-350 l/min 180-250 g/h
ELECTRICAL SYSTEM Total installed power Main switch Standard voltages Voltage fluctuation Starting method Cable reel - Capacity (rubber cable) Lighting (24 V) - Working lights - Driving lights
70 k 1 x MSE 0 380...690 V / 50 or 60 Hz Max ±10 Direct sta 1 x TCR 130 m - 33 mm O. 2 x 35 W HID, fron 2 x 70 W, rea 2 x 70 W, fron 2 x 70 W, rea
FULL DIESEL VERSION OPTIONAL Water-cooled engine Deutz BF4M 2012 - Max. rating at 2200 rpm 93 kW (125 hp Fuel tank capacity 240 liter Compressor & water pump driven by hydraulic motors Total machine weight 10 500 k
79 (94)
DD310-26
TECHNICAL DATA
Technical Specification 6-232 S-E 2007-06-01
Sandvik DD310-26
COVERAGE AREA
Extra coverage with manual override Auto-parallel coverage
5890
5190
DD310-26 on jacks. All dimensions in mm.
1750 5510 6490
OPTIONAL EQUIPMENT DRILLING SYSTEM
CARRIER
*) HL 510S rock drill. *) Telescopic feed TFX 500 series. TRS two rod system with controls (incl. TRR 1). *) Rod retainer TRR 1. *) B 26 NV boom. Drill angle measuring instrument TMS D1. Auto air flushing on rock drill return. *) SLU 1 shank lubricating device. *) Double flushing (air/water) with CT 10 compressor (incl. 2 x 60 l air receiving). *) Double flushing (air/water) with 11 kW CT 16 compressor (incl. 2 x 60 l air receiving). Air cleaner IP5 plus auxiliary connection for mine air network. *) Air mist flushing kit for auxiliary water/air connection. *) Drilling on both electric and Diesel.
Complete spare wheel. Hand pump for manual brake release. *) Stainless steel 350 l water tank. *) Exhaust scrubber.
ELECTRICAL SYSTEM *) 1 000 V electric power supply. Ground fault and overcurrent unit VYK Electric cable rubber ou PUR. *) Star-Delta electric starting method (380...690 V only). 2 x 35 W High Intensity Discharge (HID) extra working lights.
OTHER OPTIONAL EQUIPMENT Fire extinguisher (bottle only). Manual fire suppression system ANSUL, 6 nozzles. Pressure cleaning system (10 bar) with reel. Automatic water hose reel (60 m capacity). Water hose 1”½. *) Electric filling pump for oil. Greasing reel with pump and nozzle. Centralized greasing. Automatic lubrication system (Lincoln). Biodegradable oils. Fast filling and evacuation system (Wiggins) for fuel. Fast filling and evacuation system (Wiggins) for fuel, transmission, engine and hydraulic oil. *) EU, UL, CSA, AUS norms package.. Manuals other than French/English language. *) replaces standard component.
80 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
Technical Specification 4-200 S-D 2004-07-12
Boom Swing Boom Extension Divergence
Feed Swing
Feed Extension
Boom Lift
(main)
Feed Swing (slave)
Feed Tilt
Feed Roll-over
Ensure horizontal // Ensure vertical //
APPLICATION
DESCRIPTION
B 26 F boom is designed for Tamrock Axera 5, Axera 6 and Axera LP jumbos.
The x-y coordinated boom movements together with 360° actuator roll-over make the use of the boom simple and logical. Accurate automatic parallel holding both in vertical and horizontal plane improves the drilling performance and accuracy.
B 26 F boom is a hydraulic universal roll-over boom for mechanized tunnelling, drifting, cross-cutting and bolthole drilling in medium sections. It can also be used for production drilling with cut-and-fill and room-and-pillar methods. This parallel holding telescopic boom offer large «true» rectangular face coverage area.
Large dimensioned rectangular profile,adjustable and sealed boom extension wear-pieces, large diameter bearings, sealed main joints, expanding pins in cylinder joints and use of super strong cast pieces in most stressed areas are some of the features that are included to the boom design for improved reliability.
TECHNICAL DATA Coverage with parallelism holding Coverage with manual override Weight, without hoses Weight allowed Boom telescopic extension Boom lift, up and down Boom swing, symmetric Feed tilt, up and down Feed swing, symmetric Divergence, up and down Feed extension Feed roll-over
78494380 - 05-06-2007 SR-RB-FL
29,2 m² 38,9 m² 1 850 kg 1 050 kg 1 200 mm 45° and 16° ± 45° 25° and 50° ± 50° 3° and 90° 1 600 mm 360°
81 (94)
DD310-26
TECHNICAL DATA
COVERAGE AREA
6000
5300
1870
5510 6490
GENERAL DIMENSIONS
1253
2600
3°
45°
1600
90°
356
360° 572
16° 25°
50°
1200
50°
50°
82 (94)
31° (45°)
26° (45°)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
Technical Specification 4-501 S-C 2003-10-21
Boom Swing Boom Extension
Feed Roll-over
Feed Extension
Boom Lift Feed Swing (main)
Feed Swing (slave)
Feed Tilt Divergence Ensure horizontal //
Feed Angle
Ensure vertical //
APPLICATION
DESCRIPTION
B 26 NV boom is designed for Tamrock Axera 5 and Axera 6 jumbos.
The x-y coordinated boom movements together with double rotation device allows a vertical positioning of the feed on both side of the boom and the possibility to drill extremely close to the hanging and foot walls, both to the right and left, with the rock drill always in the operator’s sight line. Accurate automatic parallel holding both in vertical and horizontal plane improves the drilling performance and accuracy.
B 26 NV boom is a multi-purpose hydraulic boom for mechanized tunnelling, drifting, cross-cutting and bolthole drilling in medium sections. It can also be used for production drilling with cut-and-fill and room-and-pillar methods. This parallel holding telescopic boom offer large «true» rectangular face coverage area.
TECHNICAL DATA Coverage with parallelism holding Coverage with manual override Weight, without hoses Weight allowed Boom telescopic extension Boom lift, up and down Boom swing, symmetric Feed tilt, up and down Feed swing, symmetric Divergence, up and down Feed extension Feed roll-over Feed angle
78494380 - 05-06-2007 SR-RB-FL
29,2 m² 38,9 m² 1 900 kg 850 kg 1 200 mm 45° and 16° ± 45° 25° and 50° ± 50° 20° and 90° 1 400 mm 360° ± 95°
Large dimensioned rectangular profile,adjustable and sealed boom extension wear-pieces, large diameter bearings, sealed main joints, expanding pins in cylinder joints and use of super strong cast pieces in most stressed areas are some of the features that are included to the boom design for improved reliability.
83 (94)
DD310-26
TECHNICAL DATA
COVERAGE AREA
3410
1870 5970 5270
1200
6250 1870 3630 5655 5500 6480
GENERAL DIMENSIONS
1030
1400
2600
20°
360°
90°
45°
± 95°
16° 25°
1200
84 (94)
95°
50°
95°
50°
572
50°
31° (45°)
26° (45°)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
78494380 - 05-06-2007 SR-RB-FL
85 (94)
DD310-26
TECHNICAL DATA
86 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
78494380 - 05-06-2007 SR-RB-FL
87 (94)
DD310-26
TECHNICAL DATA
88 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
Technical Specification 3-1600 2005-02-15
1 2
3
4
5
7 6
11
10
8
12
9
APPLICATION
MAIN COMPONENTS
TFX 500 telescopic feeds are designed for Tamrock face drilling jumbos with HLX5 series rock drills. A versatile feed for face drilling, bolt hole drilling and cross-cuttings in a limited space where both long and short rods have to be used.
1. 2. 3.
DESCRIPTION The design of the feeds aims at simplicity of structure and ease of maintenance. The TFX feed consists of TF feed and TFX extension kit. When the TFX 500 feed is in minimum length, short holes can be drilled and while in maximum length, long holes can be drilled. The extension of feed can be adjusted stepless between minimum and maximum. During drilling the buffer is pushed to the rock by feed extension cylinder. The TF feed beam moves on the lower beam by lower feed cylinder. The beams are made of special aluminum profile with sliding surfaces faced with stainless steel strips. The drill rod centralizers are equipped with hardened steel wear pieces and are designed for optimum visibility and durability.
78494380 - 05-06-2007 SR-RB-FL
4. 5. 6. 7. 8. 9. 10. 11. 12.
Hose reel Feed cylinder Impulse cylinders for stop-and-return automatics Hose support Travelling centralizer Feed wire ropes and rope tensioning assembly Feed beam Lower feed cylinder Bracket for feed extension cylinder Lower feed beam Front drill rod centralizer Buffer
OPTIONAL EQUIPMENT TRR 1 hydraulic drill rod retainer for extension drilling Internal hosing Connections parts for boom Connections parts for rock drill Centralizer wear pieces of different sizes
TECHNICAL DATA Max feed force Free speed
25 kN 0.5 m/s
89 (94)
DD310-26
TECHNICAL DATA
Technical Specification 3-1600 2005-02-15
DIMENSIONS
Total length min / max
* The TFX feed doesn’t include the rock drill
TFX 500
6/12
8/14
10/16
Total length (mm)
3480 / 5310
4090 / 5920
4700 / 6530
Feed travel (mm)
1610 / 3440
2220 / 4050
2830 / 4660
636
673
710
6, 8, 10, 12
6, 8, 10, 12
6, 8, 10, 12
With following TB booms
40, 60, 90, 120, 150
40, 60, 90, 120, 150
60, 90, 120, 150
With following B26 booms
F, XLF, NV, XLNV
F, XLF, NV, XLNV
F, XLF, NV, XLNV
Net Weight (kg) With optional TRR1 rod retainer: - 1. rod length (ft)
90 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26
TECHNICAL DATA
HYDRAULIC ROCK DRILL HLX5
2-1852-A 2005-10-31
1/2
7
1100 955
295
7 8
0 4 2 3 5 1
HYDRAULIC ROCK DRILL HLX5 Application The HLX5 hydraulic rock drill is designed for tunneling and mine development drilling with Tamrock Axera jumbos. It is also suitable for bolt hole, exploration and injection hole drilling.
Description The HLX5 is a hydraulic percussive rock drill with independent reversible rotation and low profile height.
78494380 - 05-06-2007 SR-RB-FL
91 (94)
DD310-26
TECHNICAL DATA
Technical data Drill steels Shank Hole diameter Tunneling Cut hole drilling Weight Length Profile height
R 39 or Hex 35 mm drifter rods, MF-rods highly recommended Ø 45 / T 38 43...64 mm 76...127 mm 210 kg 955 mm 87 mm
Percussion mechanism Operating pressure Percussion rate Impact energy Flow (at 220 bar)
120…220 bar 67 Hz 320 Joule 97 l/min
Accumulator Accumulator gas High pressure (HP) Low pressure (LP) Filling valve
Nitrogen N2 50 bar 4 bar Vg8 DIN 7756
Rotation mechanism Motor Motor type Flow (at max. speed) Pressure max. Torque (at 175 bar) Rotation speed
Orbit type OMS 80 46 l/min 175 bar 400 Nm 0…250 rpm
Flushing Water flow (with one rod) Water pressure Shank lubrication Air flow (at 6 bar) Pressure Oil consumption Working temperature (water flushing) Ambient temperature Oil operating temperature Hose fittings size Percussion Rotation Lubrication Flushing Oil recommended
OMS 125 72 l/min 175 bar 625 Nm 0…250 rpm
OMS 160 74 l/min 175 bar 780 Nm 0…200 rpm
60 l/min (15 bar) 10...20 bar 250...350 l/min 4...7 bar 180...250 g/h
see SLU instructions
+0 ...+40 °C +40...+60 °C JIC 1 1/16 - 12 JIC 3/4 - 16 JIC 3/4 - 16 JIC 3/4 - 16 see a separate specification
Options Special tools for HLX5, ID 55006507
92 (94)
78494380 - 05-06-2007 SR-RB-FL
DD310-26 Technical Specification 2-1150-C 2007-02-14
TECHNICAL DATA
Hydraulic rock drill HL 510 S/F
APPLICATION
MAIN SPECIFICATIONS
The HL 510 S/F hydraulic rock drill is designed for face, bol and long hole drilling. HL 510 S-45 is standard for Axera face drilling jumbos. HL 510 S-38 is standard for Robolt bolters and Solo or Cabolt long hole drilling jumbos. HL 510 F is standard for Robolt bolters.
Hole diameter Drifting Cut hole drilling Bolt drilling Long hole drilling Power class Percussion rate Operating pressure Percussion Rotation (max) Rotation motor type Drill steels Drifting Bolting
MAIN CHARACTERISTICS The HL 510 S/F is a compact, robust and universal hydraulic rock drill. It is known of its hydraulic efficiency and high penetration rate. HL 510 S/F has excellent serviceability through modularly construction and visual wear indicators. Robustness is achieved by only few pressurized seems between functional modules. Thus HL 510 S/F high efficiency in action with minimized down time. Biodegradable oils can be used both in hydraulic and in shank lubrication to reduce risk of environment.
78494380 - 05-06-2007 SR-RB-FL
43...51 mm 76...127 mm 32...45 mm 48...64 mm 16 kW 59 Hz 120 - 175 bar 175 bar OMSU 80/125
Long hole drilling
H32 or H35 drifter rods H25 or H28 drifter rods Ø32 integral steels R39 or H35 MF-rods
HL 510 S-45 HL 510 S-38 HL 510 F
Ø 45/500 - T38 (R38) Ø 38/460 - R32 Ø 45/350 - R32
Shanks
93 (94)